Internet Engineering Task Force (IETF) A. Doria, Ed.
Request for Comments: 5810 Lulea University of Technology
Category: Standards Track J. Hadi Salim, Ed.
ISSN: 2070-1721 Znyx
R. Haas, Ed.
IBM
H. Khosravi, Ed.
Intel
W. Wang, Ed.
L. Dong
Zhejiang Gongshang University
R. Gopal
Nokia
J. Halpern
March 2010
Forwarding and Control Element Separation (ForCES)
Protocol Specification
Abstract
This document specifies the Forwarding and Control Element Separation
(ForCES) protocol. The ForCES protocol is used for communications
between Control Elements(CEs) and Forwarding Elements (FEs) in a
ForCES Network Element (ForCES NE). This specification is intended
to meet the ForCES protocol requirements defined in RFC 3654.
Besides the ForCES protocol, this specification also defines the
requirements for the Transport Mapping Layer (TML).
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc5810.
Doria, et al. Standards Track [Page 1]
RFC 5810 ForCES March 2010
Copyright Notice
Copyright (c) 2010 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Doria, et al. Standards Track [Page 2]
RFC 5810 ForCES March 2010
Table of Contents
1. Introduction ....................................................5
2. Terminology and Conventions .....................................6
2.1. Requirements Language ......................................6
2.2. Other Notation .............................................6
2.3. Integers ...................................................6
3. Definitions .....................................................6
4. Overview .......................................................10
4.1. Protocol Framework ........................................11
4.1.1. The PL .............................................13
4.1.2. The TML ............................................14
4.1.3. The FEM/CEM Interface ..............................14
4.2. ForCES Protocol Phases ....................................15
4.2.1. Pre-association ....................................16
4.2.2. Post-association ...................................18
4.3. Protocol Mechanisms .......................................19
4.3.1. Transactions, Atomicity, Execution, and Responses ..19
4.3.2. Scalability ........................................25
4.3.3. Heartbeat Mechanism ................................26
4.3.4. FE Object and FE Protocol LFBs .....................27
4.4. Protocol Scenarios ........................................27
4.4.1. Association Setup State ............................27
4.4.2. Association Established State or Steady State ......29
5. TML Requirements ...............................................31
5.1. TML Parameterization ......................................34
6. Message Encapsulation ..........................................35
6.1. Common Header .............................................35
6.2. Type Length Value (TLV) Structuring .......................40
6.2.1. Nested TLVs ........................................41
6.2.2. Scope of the T in TLV ..............................41
6.3. ILV .......................................................41
6.4. Important Protocol Encapsulations .........................42
6.4.1. Paths ..............................................42
6.4.2. Keys ...............................................42
6.4.3. DATA TLVs ..........................................43
6.4.4. Addressing LFB Entities ............................43
7. Protocol Construction ..........................................44
7.1. Discussion on Encoding ....................................48
7.1.1. Data Packing Rules .................................48
7.1.2. Path Flags .........................................49
7.1.3. Relation of Operational Flags with Global
Message Flags ......................................49
7.1.4. Content Path Selection .............................49
7.1.5. LFBselect-TLV ......................................49
7.1.6. OPER-TLV ...........................................50
7.1.7. RESULT TLV .........................................52
7.1.8. DATA TLV ...........................................55
Doria, et al. Standards Track [Page 3]
RFC 5810 ForCES March 2010
7.1.9. SET and GET Relationship ...........................56
7.2. Protocol Encoding Visualization ...........................56
7.3. Core ForCES LFBs ..........................................59
7.3.1. FE Protocol LFB ....................................60
7.3.2. FE Object LFB ......................................63
7.4. Semantics of Message Direction ............................63
7.5. Association Messages ......................................64
7.5.1. Association Setup Message ..........................64
7.5.2. Association Setup Response Message .................66
7.5.3. Association Teardown Message .......................68
7.6. Configuration Messages ....................................69
7.6.1. Config Message .....................................69
7.6.2. Config Response Message ............................71
7.7. Query Messages ............................................73
7.7.1. Query Message ......................................73
7.7.2. Query Response Message .............................75
7.8. Event Notification Message ................................77
7.9. Packet Redirect Message ...................................79
7.10. Heartbeat Message ........................................82
8. High Availability Support ......................................83
8.1. Relation with the FE Protocol .............................83
8.2. Responsibilities for HA ...................................86
9. Security Considerations ........................................87
9.1. No Security ...............................................87
9.1.1. Endpoint Authentication ............................88
9.1.2. Message Authentication .............................88
9.2. ForCES PL and TML Security Service ........................88
9.2.1. Endpoint Authentication Service ....................88
9.2.2. Message Authentication Service .....................89
9.2.3. Confidentiality Service ............................89
10. Acknowledgments ...............................................89
11. References ....................................................89
11.1. Normative References .....................................89
11.2. Informative References ...................................90
Appendix A. IANA Considerations ..................................91
A.1. Message Type Namespace ....................................91
A.2. Operation Selection .......................................92
A.3. Header Flags ..............................................93
A.4. TLV Type Namespace ........................................93
A.5. RESULT-TLV Result Values ..................................94
A.6. Association Setup Response ................................94
A.7. Association Teardown Message ..............................95
Appendix B. ForCES Protocol LFB Schema ...........................96
B.1. Capabilities .............................................102
B.2. Components ...............................................102
Appendix C. Data Encoding Examples ..............................103
Appendix D. Use Cases ...........................................107
Doria, et al. Standards Track [Page 4]
RFC 5810 ForCES March 2010
1. Introduction
Forwarding and Control Element Separation (ForCES) defines an
architectural framework and associated protocols to standardize
information exchange between the control plane and the forwarding
plane in a ForCES Network Element (ForCES NE). RFC 3654 has defined
the ForCES requirements, and RFC 3746 has defined the ForCES
framework. While there may be multiple protocols used within the
overall ForCES architecture, the terms "ForCES protocol" and
"protocol" as used in this document refer to the protocol used to
standardize the information exchange between Control Elements (CEs)
and Forwarding Elements (FEs) only.
The ForCES FE model [RFC5812] presents a formal way to define FE
Logical Function Blocks (LFBs) using XML. LFB configuration
components, capabilities, and associated events are defined when the
LFB is formally created. The LFBs within the FE are accordingly
controlled in a standardized way by the ForCES protocol.
This document defines the ForCES protocol specifications. The ForCES
protocol works in a master-slave mode in which FEs are slaves and CEs
are masters. The protocol includes commands for transport of LFB
configuration information, association setup, status, event
notifications, etc.
Section 3 provides a glossary of terminology used in the
specification.
Section 4 provides an overview of the protocol, including a
discussion on the protocol framework and descriptions of the Protocol
Layer (PL), a Transport Mapping Layer (TML), and the ForCES protocol
mechanisms. Section 4.4 describes several protocol scenarios and
includes message exchange descriptions.
While this document does not define the TML, Section 5 details the
services that a TML MUST provide (TML requirements).
The ForCES protocol defines a common header for all protocol
messages. The header is defined in Section 6.1, while the protocol
messages are defined in Section 7.
Section 8 describes the protocol support for high-availability
mechanisms including redundancy and fail over.
Section 9 defines the security mechanisms provided by the PL and TML.
Doria, et al. Standards Track [Page 5]
RFC 5810 ForCES March 2010
2. Terminology and Conventions
2.1. Requirements Language
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
2.2. Other Notation
In Table 1 and Table 2, the following notation is used to indicate
multiplicity:
(value)+ .... means "1 or more instances of value"
(value)* .... means "0 or more instances of value"
2.3. Integers
All integers are to be coded as unsigned binary integers of
appropriate length.
3. Definitions
This document follows the terminology defined by the ForCES
requirements in [RFC3654] and by the ForCES framework in [RFC3746].
The definitions be are repeated below for clarity.
Addressable Entity (AE):
A physical device that is directly addressable given some
interconnect technology. For example, on IP networks, it is a device
that can be reached using an IP address; and on a switch fabric, it
is a device that can be reached using a switch fabric port number.
Control Element (CE):
A logical entity that implements the ForCES protocol and uses it to
instruct one or more FEs on how to process packets. CEs handle
functionality such as the execution of control and signaling
protocols.
Doria, et al. Standards Track [Page 6]
RFC 5810 ForCES March 2010
CE Manager (CEM):
A logical entity responsible for generic CE management tasks. It is
particularly used during the pre-association phase to determine with
which FE(s) a CE should communicate. This process is called FE
discovery and may involve the CE manager learning the capabilities of
available FEs.
Data Path:
A conceptual path taken by packets within the forwarding plane inside
an FE.
Forwarding Element (FE):
A logical entity that implements the ForCES protocol. FEs use the
underlying hardware to provide per-packet processing and handling as
directed/controlled by one or more CEs via the ForCES protocol.
FE Model:
A model that describes the logical processing functions of an FE.
The FE model is defined using Logical Function Blocks (LFBs).
FE Manager (FEM):
A logical entity responsible for generic FE management tasks. It is
used during the pre-association phase to determine with which CE(s)
an FE should communicate. This process is called CE discovery and
may involve the FE manager learning the capabilities of available
CEs. An FE manager may use anything from a static configuration to a
pre-association phase protocol (see below) to determine which CE(s)
to use. Being a logical entity, an FE manager might be physically
combined with any of the other logical entities such as FEs.
ForCES Network Element (NE):
An entity composed of one or more CEs and one or more FEs. To
entities outside an NE, the NE represents a single point of
management. Similarly, an NE usually hides its internal organization
from external entities.
Doria, et al. Standards Track [Page 7]
RFC 5810 ForCES March 2010
High Touch Capability:
This term will be used to apply to the capabilities found in some
forwarders to take action on the contents or headers of a packet
based on content other than what is found in the IP header. Examples
of these capabilities include quality of service (QoS) policies,
virtual private networks, firewall, and L7 content recognition.
Inter-FE Topology:
See FE Topology.
Intra-FE Topology:
See LFB Topology.
LFB (Logical Function Block):
The basic building block that is operated on by the ForCES protocol.
The LFB is a well-defined, logically separable functional block that
resides in an FE and is controlled by the CE via the ForCES protocol.
The LFB may reside at the FE's data path and process packets or may
be purely an FE control or configuration entity that is operated on
by the CE. Note that the LFB is a functionally accurate abstraction
of the FE's processing capabilities, but not a hardware-accurate
representation of the FE implementation.
FE Topology:
A representation of how the multiple FEs within a single NE are
interconnected. Sometimes this is called inter-FE topology, to be
distinguished from intra-FE topology (i.e., LFB topology).
LFB Class and LFB Instance:
LFBs are categorized by LFB classes. An LFB instance represents an
LFB class (or type) existence. There may be multiple instances of
the same LFB class (or type) in an FE. An LFB class is represented
by an LFB class ID, and an LFB instance is represented by an LFB
instance ID. As a result, an LFB class ID associated with an LFB
instance ID uniquely specifies an LFB existence.
Doria, et al. Standards Track [Page 8]
RFC 5810 ForCES March 2010
LFB Meta Data:
Meta data is used to communicate per-packet state from one LFB to
another, but is not sent across the network. The FE model defines
how such meta data is identified, produced, and consumed by the LFBs.
It defines the functionality but not how meta data is encoded within
an implementation.
LFB Component:
Operational parameters of the LFBs that must be visible to the CEs
are conceptualized in the FE model as the LFB components. The LFB
components include, for example, flags, single parameter arguments,
complex arguments, and tables that the CE can read and/or write via
the ForCES protocol (see below).
LFB Topology:
Representation of how the LFB instances are logically interconnected
and placed along the data path within one FE. Sometimes it is also
called intra-FE topology, to be distinguished from inter-FE topology.
Pre-association Phase:
The period of time during which an FE manager and a CE manager are
determining which FE(s) and CE(s) should be part of the same network
element.
Post-association Phase:
The period of time during which an FE knows which CE is to control it
and vice versa. This includes the time during which the CE and FE
are establishing communication with one another.
ForCES Protocol:
While there may be multiple protocols used within the overall ForCES
architecture, the terms "ForCES protocol" and "protocol" refer to the
Fp reference points in the ForCES framework in [RFC3746]. This
protocol does not apply to CE-to-CE communication, FE-to-FE
communication, or communication between FE and CE managers.
Basically, the ForCES protocol works in a master-slave mode in which
FEs are slaves and CEs are masters. This document defines the
specifications for this ForCES protocol.
Doria, et al. Standards Track [Page 9]
RFC 5810 ForCES March 2010
ForCES Protocol Layer (ForCES PL):
A layer in the ForCES protocol architecture that defines the ForCES
protocol messages, the protocol state transfer scheme, and the ForCES
protocol architecture itself (including requirements of ForCES TML as
shown below). Specifications of ForCES PL are defined by this
document.
ForCES Protocol Transport Mapping Layer (ForCES TML):
A layer in ForCES protocol architecture that uses the capabilities of
existing transport protocols to specifically address protocol message
transportation issues, such as how the protocol messages are mapped
to different transport media (like TCP, IP, ATM, Ethernet, etc.), and
how to achieve and implement reliability, multicast, ordering, etc.
The ForCES TML specifications are detailed in separate ForCES
documents, one for each TML.
4. Overview
The reader is referred to the framework document [RFC3746], and in
particular, Sections 3 and 4, for an architectural overview and an
explanation of how the ForCES protocol fits in. There may be some
content overlap between the framework document and this section in
order to provide clarity. This document is authoritative on the
protocol, whereas [RFC3746] is authoritative on the architecture.
Doria, et al. Standards Track [Page 10]
RFC 5810 ForCES March 2010
4.1. Protocol Framework
Figure 1 below is reproduced from the framework document for clarity.
It shows an NE with two CEs and two FEs.
---------------------------------------
| ForCES Network Element |
-------------- Fc | -------------- -------------- |
| CE Manager |---------+-| CE 1 |------| CE 2 | |
-------------- | | | Fr | | |
| | -------------- -------------- |
| Fl | | | Fp / |
| | Fp| |----------| / |
| | | |/ |
| | | | |
| | | Fp /|----| |
| | | /--------/ | |
-------------- Ff | -------------- -------------- |
| FE Manager |---------+-| FE 1 | Fi | FE 2 | |
-------------- | | |------| | |
| -------------- -------------- |
| | | | | | | | | |
----+--+--+--+----------+--+--+--+-----
| | | | | | | |
| | | | | | | |
Fi/f Fi/f
Fp: CE-FE interface
Fi: FE-FE interface
Fr: CE-CE interface
Fc: Interface between the CE manager and a CE
Ff: Interface between the FE manager and an FE
Fl: Interface between the CE manager and the FE manager
Fi/f: FE external interface
Figure 1: ForCES Architectural Diagram
The ForCES protocol domain is found in the Fp reference points. The
Protocol Element configuration reference points, Fc and Ff, also play
a role in the booting up of the ForCES protocol. The protocol
element configuration (indicated by reference points Fc, Ff, and Fl
in [RFC3746]) is out of scope of the ForCES protocol but is touched
on in this document in discussion of FEM and CEM since it is an
integral part of the protocol pre-association phase.
Doria, et al. Standards Track [Page 11]
RFC 5810 ForCES March 2010
Figure 2 below shows further breakdown of the Fp interfaces by means
of the example of an MPLS QoS-enabled Network Element.
-------------------------------------------------
| | | | | | |
|OSPF |RIP |BGP |RSVP |LDP |. . . |
| | | | | | |
------------------------------------------------- CE
| ForCES Interface |
-------------------------------------------------
^ ^
| |
ForCES | |data
control | |packets
messages| |(e.g., routing packets)
| |
v v
-------------------------------------------------
| ForCES Interface |
------------------------------------------------- FE
| | | | | | |
|LPM Fwd|Meter |Shaper |MPLS |Classi-|. . . |
| | | | |fier | |
-------------------------------------------------
Figure 2: Examples of CE and FE Functions
The ForCES interface shown in Figure 2 constitutes two pieces: the PL
and the TML.
Doria, et al. Standards Track [Page 12]
RFC 5810 ForCES March 2010
This is depicted in Figure 3 below.
+------------------------------------------------
| CE PL |
+------------------------------------------------
| CE TML |
+------------------------------------------------
^
|
ForCES | (i.e., ForCES data + control
PL | packets )
messages |
over |
specific |
TML |
encaps |
and |
transport |
|
v
+------------------------------------------------
| FE TML |
+------------------------------------------------
| FE PL |
+------------------------------------------------
Figure 3: ForCES Interface
The PL is in fact the ForCES protocol. Its semantics and message
layout are defined in this document. The TML layer is necessary to
connect two ForCES PLs as shown in Figure 3 above. The TML is out of
scope for this document but is within scope of ForCES. This document
defines requirements the PL needs the TML to meet.
Both the PL and the TML are standardized by the IETF. While only one
PL is defined, different TMLs are expected to be standardized. To
interoperate, the TML at the CE and FE are expected to conform to the
same definition.
On transmit, the PL delivers its messages to the TML. The local TML
delivers the message to the destination TML. On receive, the TML
delivers the message to its destination PL.
4.1.1. The PL
The PL is common to all implementations of ForCES and is standardized
by the IETF as defined in this document. The PL is responsible for
associating an FE or CE to an NE. It is also responsible for tearing
Doria, et al. Standards Track [Page 13]
RFC 5810 ForCES March 2010
down such associations. An FE uses the PL to transmit various
subscribed-to events to the CE PL as well as to respond to various
status requests issued from the CE PL. The CE configures both the FE
and associated LFBs' operational parameters using the PL. In
addition, the CE may send various requests to the FE to activate or
deactivate it, reconfigure its HA parameterization, subscribe to
specific events, etc. More details can be found in Section 7.
4.1.2. The TML
The TML transports the PL messages. The TML is where the issues of
how to achieve transport-level reliability, congestion control,
multicast, ordering, etc. are handled. It is expected that more than
one TML will be standardized. The various possible TMLs could vary
their implementations based on the capabilities of underlying media
and transport. However, since each TML is standardized,
interoperability is guaranteed as long as both endpoints support the
same TML. All ForCES protocol layer implementations MUST be portable
across all TMLs, because all TMLs MUST have the top-edge semantics
defined in this document.
4.1.3. The FEM/CEM Interface
The FEM and CEM components, although valuable in the setup and
configurations of both the PL and TML, are out of scope of the ForCES
protocol. The best way to think of them is as configurations/
parameterizations for the PL and TML before they become active (or
even at runtime based on implementation). In the simplest case, the
FE or CE reads a static configuration file. RFC 3746 has a more
detailed description on how the FEM and CEM could be used. The pre-
association phase, where the CEM and FEM can be used, are described
briefly in Section 4.2.1.
An example of typical things the FEM/CEM could configure would be
TML-specific parameterizations such as:
a. How the TML connection should happen (for example, what IP
addresses to use, transport modes, etc.)
b. The ID for the FE (FEID) or CE (CEID) (which would also be issued
during the pre-association phase)
c. Security parameterization such as keys, etc.
d. Connection association parameters
Doria, et al. Standards Track [Page 14]
RFC 5810 ForCES March 2010
An example of connection association parameters might be:
o simple parameters: send up to 3 association messages every 1
second
o complex parameters: send up to 4 association messages with
increasing exponential timeout
4.2. ForCES Protocol Phases
ForCES, in relation to NEs, involves two phases: the pre-association
phase where configuration/initialization/bootup of the TML and PL
layer happens, and the post-association phase where the ForCES
protocol operates to manipulate the parameters of the FEs.
CE sends Association Setup
+---->--->------------>---->---->---->------->----+
| Y
^ |
| Y
+---+-------+ +-------------+
|FE pre- | | FE post- |
|association| CE sends Association Teardown | association |
|phase |<------- <------<-----<------<-------+ phase |
| | | |
+-----------+ +-------------+
^ Y
| |
+-<---<------<-----<------<----<---------<------+
FE loses association
Figure 4: The FE Protocol Phases
In the mandated case, once associated, the FE may forward packets
depending on the configuration of its specific LFBs. An FE that is
associated to a CE will continue sending packets until it receives an
Association Teardown Message or until it loses association. An
unassociated FE MAY continue sending packets when it has a high
availability capability. The extra details are explained in
Section 8 and not discussed here to allow for a clear explanation of
the basics.
The FE state transitions are controlled by means of the FE Object LFB
FEState component, which is defined in [RFC5812], Section 5.1, and
also explained in Section 7.3.2.
Doria, et al. Standards Track [Page 15]
RFC 5810 ForCES March 2010
The FE initializes in the FEState OperDisable. When the FE is ready
to process packets in the data path, it transitions itself to the
OperEnable state.
The CE may decide to pause the FE after it already came up as
OperEnable. It does this by setting the FEState to AdminDisable.
The FE stays in the AdminDisable state until it is explicitly
configured by the CE to transition to the OperEnable state.
When the FE loses its association with the CE, it may go into the
pre-association phase depending on the programmed policy. For the FE
to properly complete the transition to the AdminDisable state, it
MUST stop packet forwarding and this may impact multiple LFBS. How
this is achieved is outside the scope of this specification.
4.2.1. Pre-association
The ForCES interface is configured during the pre-association phase.
In a simple setup, the configuration is static and is typically read
from a saved configuration file. All the parameters for the
association phase are well known after the pre-association phase is
complete. A protocol such as DHCP may be used to retrieve the
configuration parameters instead of reading them from a static
configuration file. Note, this will still be considered static pre-
association. Dynamic configuration may also happen using the Fc, Ff,
and Fl reference points (refer to [RFC3746]). Vendors may use their
own proprietary service discovery protocol to pass the parameters.
Essentially, only guidelines are provided here and the details are
left to the implementation.
The following are scenarios reproduced from the framework document to
show a pre-association example.
Doria, et al. Standards Track [Page 16]
RFC 5810 ForCES March 2010
<----Ff ref pt---> <--Fc ref pt------->
FE Manager FE CE Manager CE
| | | |
| | | |
(security exchange) (security exchange)
1|<------------>| authentication 1|<----------->|authentication
| | | |
(FE ID, components) (CE ID, components)
2|<-------------| request 2|<------------|request
| | | |
3|------------->| response 3|------------>|response
(corresponding CE ID) (corresponding FE ID)
| | | |
| | | |
Figure 5: Examples of a Message Exchange over the Ff and Fc
Reference Points
<-----------Fl ref pt--------------> |
FE Manager FE CE Manager CE
| | | |
| | | |
(security exchange) | |
1|<------------------------------>| |
| | | |
(a list of CEs and their components) |
2|<-------------------------------| |
| | | |
(a list of FEs and their components) |
3|------------------------------->| |
| | | |
| | | |
Figure 6: Example of a Message Exchange over the Fl Reference Point
Before the transition to the association phase, the FEM will have
established contact with a CEM component. Initialization of the
ForCES interface will have completed, and authentication as well as
capability discovery may be complete. Both the FE and CE would have
the necessary information for connecting to each other for
configuration, accounting, identification, and authentication
purposes. To summarize, at the completion of this stage both sides
have all the necessary protocol parameters such as timers, etc. The
Fl reference point may continue to operate during the association
phase and may be used to force a disassociation of an FE or CE. The
specific interactions of the CEM and the FEM that are part of the
Doria, et al. Standards Track [Page 17]
RFC 5810 ForCES March 2010
pre-association phase are out of scope; for this reason, these
details are not discussed any further in this specification. The
reader is referred to the framework document [RFC3746] for a slightly
more detailed discussion.
4.2.2. Post-association
In this phase, the FE and CE components communicate with each other
using the ForCES protocol (PL over TML) as defined in this document.
There are three sub-phases:
o Association Setup Stage
o Established Stage
o Association Lost Stage
4.2.2.1. Association Setup Stage
The FE attempts to join the NE. The FE may be rejected or accepted.
Once granted access into the NE, capabilities exchange happens with
the CE querying the FE. Once the CE has the FE capability
information, the CE can offer an initial configuration (possibly to
restore state) and can query certain components within either an LFB
or the FE itself.
More details are provided in Section 4.4.
On successful completion of this stage, the FE joins the NE and is
moved to the Established Stage.
4.2.2.2. Established Stage
In this stage, the FE is continuously updated or queried. The FE may
also send asynchronous event notifications to the CE or synchronous
heartbeat notifications if programmed to do so. This stage continues
until a termination occurs, either due to loss of connectivity or due
to a termination initiated by either the CE or the FE.
Refer to the section on protocol scenarios, Section 4.4, for more
details.
4.2.2.3. Association Lost Stage
In this stage, both or either the CE or FE declare the other side is
no longer associated. The disconnection could be initiated by either
party for administrative purposes but may also be driven by
operational reasons such as loss of connectivity.
Doria, et al. Standards Track [Page 18]
RFC 5810 ForCES March 2010
A core LFB known as the FE Protocol Object (FEPO) is defined (refer
to Appendix B and Section 7.3.1). FEPO defines various timers that
can be used in conjunction with a traffic-sensitive heartbeat
mechanism (Section 4.3.3) to detect loss of connectivity.
The loss of connectivity between TMLs does not indicate a loss of
association between respective PL layers. If the TML cannot repair
the transport loss before the programmed FEPO timer thresholds
associated with the FE is exceeded, then the association between the
respective PL layers will be lost.
FEPO defines several policies that can be programmed to define
behavior upon a detected loss of association. The FEPO's programmed
CE failover policy (refer to Sections 8, 7.3.1, 4.3.3, and B) defines
what takes place upon loss of association.
For this version of the protocol (as defined in this document), the
FE, upon re-association, MUST discard any state it has as invalid and
retrieve new state. This approach is motivated by a desire for
simplicity (as opposed to efficiency).
4.3. Protocol Mechanisms
Various semantics are exposed to the protocol users via the PL header
including transaction capabilities, atomicity of transactions, two-
phase commits, batching/parallelization, high availability, and
failover as well as command pipelines.
The EM (Execution Mode) flag, AT (Atomic Transaction) flag, and TP
(Transaction Phase) flag as defined in the common header
(Section 6.1) are relevant to these mechanisms.
4.3.1. Transactions, Atomicity, Execution, and Responses
In the master-slave relationship, the CE instructs one or more FEs on
how to execute operations and how to report the results.
This section details the different modes of execution that a CE can
order the FE(s) to perform, as defined in Section 4.3.1.1. It also
describes the different modes a CE can ask the FE(s) to use for
formatting the responses after processing the operations as
requested. These modes relate to the transactional two-phase commit
operations.
Doria, et al. Standards Track [Page 19]
RFC 5810 ForCES March 2010
4.3.1.1. Execution
There are 3 execution modes that can be requested for a batch of
operations spanning one or more LFB selectors (refer to
Section 7.1.5) in one protocol message. The EM flag defined in the
common header (Section 6.1) selects the execution mode for a protocol
message, as below:
a. execute-all-or-none
b. continue-execute-on-failure
c. execute-until-failure
4.3.1.1.1. execute-all-or-none
When set to this mode of execution, independent operations in a
message MAY be targeted at one or more LFB selectors within an FE.
All these operations are executed serially, and the FE MUST have no
execution failure for any of the operations. If any operation fails
to execute, then all the previous ones that have been executed prior
to the failure will need to be undone. That is, there is rollback
for this mode of operation.
Refer to Section 4.3.1.2.2 for how this mode is used in cases of
transactions. In such a case, no operation is executed unless a
commit is issued by the CE.
Care should be taken on how this mode is used because a mis-
configuration could result in traffic losses. To add certainty to
the success of an operation, one should use this mode in a
transactional operation as described in Section 4.3.1.2.2
4.3.1.1.2. continue-execute-on-failure
If several independent operations are targeted at one or more LFB
selectors, execution continues for all operations at the FE even if
one or more operations fail.
4.3.1.1.3. execute-until-failure
In this mode, all operations are executed on the FE sequentially
until the first failure. The rest of the operations are not executed
but operations already completed are not undone. That is, there is
no rollback in this mode of operation.
Doria, et al. Standards Track [Page 20]
RFC 5810 ForCES March 2010
4.3.1.2. Transaction and Atomicity
4.3.1.2.1. Transaction Definition
A transaction is defined as a collection of one or more ForCES
operations within one or more PL messages that MUST meet the ACIDity
properties [ACID], defined as:
Atomicity: In a transaction involving two or more discrete pieces
of information, either all of the pieces are committed
or none are.
Consistency: A transaction either creates a new and valid state of
data or, if any failure occurs, returns all data to the
state it was in before the transaction was started.
Isolation: A transaction in process and not yet committed MUST
remain isolated from any other transaction.
Durability: Committed data is saved by the system such that, even in
the event of a failure and a system restart, the data is
available in its correct state.
There are cases where the CE knows exact memory and implementation
details of the FE such as in the case of an FE-CE pair from the same
vendor where the FE-CE pair is tightly coupled. In such a case, the
transactional operations may be simplified further by extra
computation at the CE. This view is not discussed further other than
to mention that it is not disallowed.
As defined above, a transaction is always atomic and MAY be
a. Within an FE alone
Example: updating multiple tables that are dependent on each
other. If updating one fails, then any that were already updated
MUST be undone.
b. Distributed across the NE
Example: updating table(s) that are inter-dependent across
several FEs (such as L3 forwarding-related tables).
4.3.1.2.2. Transaction Protocol
By use of the execution mode, as defined in Section 4.3.1.1, the
protocol has provided a mechanism for transactional operations within
one stand-alone message. The 'execute-all-or-none' mode can meet the
ACID requirements.
Doria, et al. Standards Track [Page 21]
RFC 5810 ForCES March 2010
For transactional operations of multiple messages within one FE or
across FEs, a classical transactional protocol known as two-phase
commit (2PC) [2PCREF] is supported by the protocol to achieve the
transactional operations utilizing Config messages (Section 7.6.1).
The COMMIT and TRCOMP operations in conjunction with the AT and the
TP flags in the common header (Section 6.1) are provided for 2PC-
based transactional operations spanning multiple messages.
The AT flag, when set, indicates that this message belongs to an
Atomic Transaction. All messages for a transaction operation MUST
have the AT flag set. If not set, it means that the message is a
stand-alone message and does not participate in any transaction
operation that spans multiple messages.
The TP flag indicates the Transaction Phase to which this message
belongs. There are 4 possible phases for a transactional operation
known as:
SOT (Start of Transaction)
MOT (Middle of Transaction)
EOT (End of Transaction)
ABT (Abort)
The COMMIT operation is used by the CE to signal to the FE(s) to
commit a transaction. When used with an ABT TP flag, the COMMIT
operation signals the FE(s) to roll back (i.e., un-COMMIT) a
previously committed transaction.
The TRCOMP operation is a small addition to the classical 2PC
approach. TRCOMP is sent by the CE to signal to the FE(s) that the
transaction they have COMMITed is now over. This allows the FE(s) an
opportunity to clear state they may have kept around to perform a
roll back (if it became necessary).
A transaction operation is started with a message in which the TP
flag is set to Start of Transaction (SOT). Multi-part messages,
after the first one, are indicated by the Middle of Transaction (MOT)
flag. All messages from the CE MUST set the AlwaysACK flag
(Section 6) to solicit responses from the FE(s).
Before the CE issues a commit (described further below), the FE MUST
only validate that the operation can be executed but not execute it.
Doria, et al. Standards Track [Page 22]
RFC 5810 ForCES March 2010
Any failure notified by an FE causes the CE to abort the
transaction on all FEs involved in the transaction. This is
achieved by sending a Config message with an ABT flag and a COMMIT
operation.
If there are no failures by any participating FE, the transaction
commitment phase is signaled from the CE to the FE by an End of
Transaction (EOT) configuration message with a COMMIT operation.
The FE MUST respond to the CE's EOT message. There are two possible
failure scenarios in which the CE MUST abort the transaction (as
described above):
a. If any participating FE responds with a failure message in
relation to the transaction.
b. If no response is received from a participating FE within a
specified timeout.
If all participating FEs respond with a success indicator within the
expected time, then the CE MUST issue a TRCOMP operation to all
participating FEs. An FE MUST NOT respond to a TRCOMP.
Note that a transactional operation is generically atomic; therefore,
it requires that the execution modes of all messages in a transaction
operation should always be kept the same and be set to 'execute-all-
or-none'. If the EM flag is set to other execution modes, it will
result in a transaction failure.
As noted above, a transaction may span multiple messages. It is up
to the CE to keep track of the different outstanding messages making
up a transaction. As an example, the correlator field could be used
to mark transactions and a sequence field to label the different
messages within the same atomic transaction, but this is out of scope
and up to implementations.
4.3.1.2.3. Recovery
Any of the participating FEs or the CE or the associations between
them may fail after the EOT Response message has been sent by the FE
but before the CE has received all the responses, e.g., if the EOT
response never reaches the CE.
In this protocol revision, as indicated in Section 4.2.2.3, an FE
losing an association would be required to get entirely new state
from the newly associated CE upon a re-association. Although this
approach is simplistic and provides likeliness of losing data path
Doria, et al. Standards Track [Page 23]
RFC 5810 ForCES March 2010
traffic, it is a design choice to avoid the additional complexity of
managing graceful restarts. The HA mechanisms (Section 8) are
provided to allow for a continuous operation in case of FE failures.
Flexibility is provided on how to react when an FE loses association.
This is dictated by the CE failover policy (refer to Section 8 and
Section 7.3).
4.3.1.2.4. Transaction Messaging Example
This section illustrates an example of how a successful two-phase
commit between a CE and an FE would look in the simple case.
FE PL CE PL
| |
| (1) Config, SOT,AT, EM=All-or-None, OP= SET/DEL,etc |
|<-----------------------------------------------------|
| |
| (2) ACKnowledge |
|----------------------------------------------------->|
| |
| (3) Config, MOT,AT, EM=All-or-None, OP= SET/DEL,etc |
|<-----------------------------------------------------|
| |
| (4) ACKnowledge |
|----------------------------------------------------->|
| |
| (5) Config, MOT,AT, EM=All-or-None, OP= SET/DEL,etc |
|<-----------------------------------------------------|
| |
| (6) ACKnowledge |
|----------------------------------------------------->|
. .
. .
. .
. .
| |
| (N) Config, EOT,AT, EM=All-or-None, OP= COMMIT |
|<-----------------------------------------------------|
| |
| (N+1)Config-response, ACKnowledge, OP=COMMIT-RESPONSE|
|----------------------------------------------------->|
| |
| (N+2) Config, OP=TRCOMP |
|<-----------------------------------------------------|
Figure 7: Example of a Two-Phase Commit
Doria, et al. Standards Track [Page 24]
RFC 5810 ForCES March 2010
For the scenario illustrated above:
o In step 1, the CE issues a Config message with an operation of
choice like a DEL or SET. The transaction flags are set to
indicate a Start of Transaction (SOT), Atomic Transaction (AT),
and execute-all-or-none.
o The FE validates that it can execute the request successfully and
then issues an acknowledgment back to the CE in step 2.
o In step 3, the same sort of construct as in step 1 is repeated by
the CE with the transaction flag changed to Middle of Transaction
(MOT).
o The FE validates that it can execute the request successfully and
then issues an acknowledgment back to the CE in step 4.
o The CE-FE exchange continues in the same manner until all the
operations and their parameters are transferred to the FE. This
happens in step (N-1).
o In step N, the CE issues a commit. A commit is a Config message
with an operation of type COMMIT. The transaction flag is set to
End of Transaction (EOT). Essentially, this is an "empty" message
asking the FE to execute all the operations it has gathered since
the beginning of the transaction (message #1).
o The FE at this point executes the full transaction. It then
issues an acknowledgment back to the CE in step (N+1) that
contains a COMMIT-RESPONSE.
o The CE in this case has the simple task of issuing a TRCOMP
operation to the FE in step (N+2).
4.3.2. Scalability
It is desirable that the PL not become the bottleneck when larger
bandwidth pipes become available. To pick a hypothetical example in
today's terms, if a 100-Gbps pipe is available and there is
sufficient work, then the PL should be able to take advantage of this
and use all of the 100-Gbps pipe. Two mechanisms have been provided
to achieve this. The first one is batching and the second one is a
command pipeline.
Doria, et al. Standards Track [Page 25]
RFC 5810 ForCES March 2010
Batching is the ability to send multiple commands (such as Config) in
one Protocol Data Unit (PDU). The size of the batch will be affected
by, among other things, the path MTU. The commands may be part of
the same transaction or may be part of unrelated transactions that
are independent of each other.
Command pipelining allows for pipelining of independent transactions
that do not affect each other. Each independent transaction could
consist of one or more batches.
4.3.2.1. Batching
There are several batching levels at different protocol hierarchies.
o Multiple PL PDUs can be aggregated under one TML message.
o Multiple LFB classes and instances (as indicated in the LFB
selector) can be addressed within one PL PDU.
o Multiple operations can be addressed to a single LFB class and
instance.
4.3.2.2. Command Pipelining
The protocol allows any number of messages to be issued by the CE
before the corresponding acknowledgments (if requested) have been
returned by the FE. Hence, pipelining is inherently supported by the
protocol. Matching responses with requests messages can be done
using the correlator field in the message header.
4.3.3. Heartbeat Mechanism
Heartbeats (HBs) between FEs and CEs are traffic sensitive. An HB is
sent only if no PL traffic is sent between the CE and FE within a
configured interval. This has the effect of reducing the amount of
HB traffic in the case of busy PL periods.
An HB can be sourced by either the CE or FE. When sourced by the CE,
a response can be requested (similar to the ICMP ping protocol). The
FE can only generate HBs in the case of being configured to do so by
the CE. Refer to Section 7.3.1 and Section 7.10 for details.
Doria, et al. Standards Track [Page 26]
RFC 5810 ForCES March 2010
4.3.4. FE Object and FE Protocol LFBs
All PL messages operate on LFB constructs, as this provides more
flexibility for future enhancements. This means that maintenance and
configurability of FEs, NE, and the ForCES protocol itself MUST be
expressed in terms of this LFB architecture. For this reason,
special LFBs are created to accommodate this need.
In addition, this shows how the ForCES protocol itself can be
controlled by the very same type of structures (LFBs) it uses to
control functions such as IP forwarding, filtering, etc.
To achieve this, the following specialized LFBs are introduced:
o FE Protocol LFB, which is used to control the ForCES protocol.
o FE Object LFB, which is used to control components relative to the
FE itself. Such components include FEState [RFC5812], vendor,
etc.
These LFBs are detailed in Section 7.3.
4.4. Protocol Scenarios
This section provides a very high level description of sample message
sequences between a CE and an FE. For protocol message encoding
refer to Section 6.1, and for the semantics of the protocol refer to
Section 4.3.
4.4.1. Association Setup State
The associations among CEs and FEs are initiated via the Association
Setup message from the FE. If a Setup Request is granted by the CE,
a successful Setup Response message is sent to the FE. If CEs and
FEs are operating in an insecure environment, then the security
associations have to be established between them before any
association messages can be exchanged. The TML MUST take care of
establishing any security associations.
This is typically followed by capability query, topology query, etc.
When the FE is ready to start processing the data path, it sets the
FEO FEState component to OperEnable (refer to [RFC5812] for details)
and reports it to the CE as such when it is first queried.
Typically, the FE is expected to be ready to process the data path
before it associates, but there may be rare cases where it needs time
do some pre-processing -- in such a case, the FE will start in the
OperDisable state and when it is ready will transition to the
OperEnable state. An example of an FE starting in OperDisable then
Doria, et al. Standards Track [Page 27]
RFC 5810 ForCES March 2010
transitioning to OperEnable is illustrated in Figure 8. The CE could
at any time also disable the FE's data path operations by setting the
FEState to AdminDisable. The FE MUST NOT process packets during this
state unless the CE sets the state back to OperEnable. These
sequences of messages are illustrated in Figure 8 below.
FE PL CE PL
| |
| Asso Setup Req |
|---------------------->|
| |
| Asso Setup Resp |
|<----------------------|
| |
| LFBx Query capability |
|<----------------------|
| |
| LFBx Query Resp |
|---------------------->|
| |
| FEO Query (Topology) |
|<----------------------|
| |
| FEO Query Resp |
|---------------------->|
| |
| FEO OperEnable Event |
|---------------------->|
| |
| Config FEO Adminup |
|<----------------------|
| |
| FEO Config-Resp |
|---------------------->|
| |
Figure 8: Message Exchange between CE and FE to Establish
an NE Association
On successful completion of this state, the FE joins the NE.
Doria, et al. Standards Track [Page 28]
RFC 5810 ForCES March 2010
4.4.2. Association Established State or Steady State
In this state, the FE is continuously updated or queried. The FE may
also send asynchronous event notifications to the CE, synchronous
Heartbeat messages, or Packet Redirect message to the CE. This
continues until a termination (or deactivation) is initiated by
either the CE or FE. Figure 9 below, helps illustrate this state.
Doria, et al. Standards Track [Page 29]
RFC 5810 ForCES March 2010
FE PL CE PL
| |
| Heartbeat |
|<---------------------------->|
| |
| Heartbeat |
|----------------------------->|
| |
| Config-set LFBy (Event sub.) |
|<-----------------------------|
| |
| Config Resp LFBy |
|----------------------------->|
| |
| Config-set LFBx Component |
|<-----------------------------|
| |
| Config Resp LFBx |
|----------------------------->|
| |
|Config-Query LFBz (Stats) |
|<--------------------------- -|
| |
| Query Resp LFBz |
|----------------------------->|
| |
| FE Event Report |
|----------------------------->|
| |
| Config-Del LFBx Component |
|<-----------------------------|
| |
| Config Resp LFBx |
|----------------------------->|
| |
| Packet Redirect LFBx |
|----------------------------->|
| |
| Heartbeat |
|<-----------------------------|
. .
. .
| |
Figure 9: Message Exchange between CE and FE during
Steady-State Communication
Doria, et al. Standards Track [Page 30]
RFC 5810 ForCES March 2010
Note that the sequence of messages shown in the figure serve only as
examples and the message exchange sequences could be different from
what is shown in the figure. Also, note that the protocol scenarios
described in this section do not include all the different message
exchanges that would take place during failover. That is described
in the HA section (Section 8).
5. TML Requirements
The requirements below are expected to be met by the TML. This text
does not define how such mechanisms are delivered. As an example,
the mechanisms to meet the requirements could be defined to be
delivered via hardware or between 2 or more TML software processes on
different CEs or FEs in protocol-level schemes.
Each TML MUST describe how it contributes to achieving the listed
ForCES requirements. If for any reason a TML does not provide a
service listed below, a justification needs to be provided.
Implementations that support the ForCES protocol specification MUST
implement [RFC5811]. Note that additional TMLs might be specified in
the future, and if a new TML defined in the future that meets the
requirements listed here proves to be better, then the "MUST
implement TML" may be redefined.
1. Reliability
Various ForCES messages will require varying degrees of reliable
delivery via the TML. It is the TML's responsibility to provide
these shades of reliability and describe how the different ForCES
messages map to reliability.
The most common level of reliability is what we refer to as
strict or robust reliability in which we mean no losses,
corruption, or re-ordering of information being transported while
ensuring message delivery in a timely fashion.
Payloads such as configuration from a CE and its response from an
FE are mission critical and must be delivered in a robust
reliable fashion. Thus, for information of this sort, the TML
MUST either provide built-in protocol mechanisms or use a
reliable transport protocol for achieving robust/strict
reliability.
Doria, et al. Standards Track [Page 31]
RFC 5810 ForCES March 2010
Some information or payloads, such as redirected packets or
packet sampling, may not require robust reliability (can tolerate
some degree of losses). For information of this sort, the TML
could define to use a mechanism that is not strictly reliable
(while conforming to other TML requirements such as congestion
control).
Some information or payloads, such as heartbeat packets, may
prefer timeliness over reliable delivery. For information of
this sort, the TML could define to use a mechanism that is not
strictly reliable (while conforming to other TML requirements
such as congestion control).
2. Security
TML provides security services to the ForCES PL. Because a
ForCES PL is used to operate an NE, attacks designed to confuse,
disable, or take information from a ForCES-based NE may be seen
as a prime objective during a network attack.
An attacker in a position to inject false messages into a PL
stream can affect either the FE's treatment of the data path (for
example, by falsifying control data reported as coming from the
CE) or the CE itself (by modifying events or responses reported
as coming from the FE). For this reason, CE and FE node
authentication and TML message authentication are important.
The PL messages may also contain information of value to an
attacker, including information about the configuration of the
network, encryption keys, and other sensitive control data, so
care must be taken to confine their visibility to authorized
users.
* The TML MUST provide a mechanism to authenticate ForCES CEs
and FEs, in order to prevent the participation of unauthorized
CEs and unauthorized FEs in the control and data path
processing of a ForCES NE.
* The TML SHOULD provide a mechanism to ensure message
authentication of PL data transferred from the CE to FE (and
vice versa), in order to prevent the injection of incorrect
data into PL messages.
* The TML SHOULD provide a mechanism to ensure the
confidentiality of data transferred from the ForCES PL, in
order to prevent disclosure of PL-level information
transported via the TML.
Doria, et al. Standards Track [Page 32]
RFC 5810 ForCES March 2010
The TML SHOULD provide these services by employing TLS or IPsec.
3. Congestion control
The transport congestion control scheme used by the TML needs to
be defined. The congestion control mechanism defined by the TML
MUST prevent transport congestive collapse [RFC2914] on either
the FE or CE side.
4. Uni/multi/broadcast addressing/delivery, if any
If there is any mapping between PL- and TML-level uni/multi/
broadcast addressing, it needs to be defined.
5. HA decisions
It is expected that availability of transport links is the TML's
responsibility. However, based upon its configuration, the PL
may wish to participate in link failover schemes and therefore
the TML MUST support this capability.
Please refer to Section 8 for details.
6. Encapsulations used
Different types of TMLs will encapsulate the PL messages on
different types of headers. The TML needs to specify the
encapsulation used.
7. Prioritization
It is expected that the TML will be able to handle up to 8
priority levels needed by the PL and will provide preferential
treatment.
While the TML needs to define how this is achieved, it should be
noted that the requirement for supporting up to 8 priority levels
does not mean that the underlying TML MUST be capable of
providing up to 8 actual priority levels. In the event that the
underlying TML layer does not have support for 8 priority levels,
the supported priority levels should be divided between the
available TML priority levels. For example, if the TML only
supports 2 priority levels, 0-3 could go in one TML priority
level, while 4-7 could go in the other.
The TML MUST NOT re-order config packets with the same priority.
Doria, et al. Standards Track [Page 33]
RFC 5810 ForCES March 2010
8. Node Overload Prevention
The TML MUST define mechanisms it uses to help prevent node
overload.
Overload results in starvation of node compute cycles and/or
bandwidth resources, which reduces the operational capacity of a
ForCES NE. NE node overload could be deliberately instigated by
a hostile node to attack a ForCES NE and create a denial of
service (DoS). It could also be created by a variety of other
reasons such as large control protocol updates (e.g., BGP flaps),
which consequently cause a high frequency of CE to FE table
updates, HA failovers, or component failures, which migrate an FE
or CE load overwhelming the new CE or FE, etc. Although the
environments under which SIP and ForCES operate are different,
[RFC5390] provides a good guide to generic node requirements one
needs to guard for.
A ForCES node CPU may be overwhelmed because the incoming packet
rate is higher than it can keep up with -- in such a case, a
node's transport queues grow and transport congestion
subsequently follows. A ForCES node CPU may also be adversely
overloaded with very few packets, i.e., no transport congestion
at all (e.g., a in a DoS attack against a table hashing algorithm
that overflows the table and/or keeps the CPU busy so it does not
process other tasks). The TML node overload solution specified
MUST address both types of node overload scenarios.
5.1. TML Parameterization
It is expected that it should be possible to use a configuration
reference point, such as the FEM or the CEM, to configure the TML.
Some of the configured parameters may include:
o PL ID
o Connection Type and associated data. For example, if a TML uses
IP/TCP/UDP, then parameters such as TCP and UDP port and IP
addresses need to be configured.
o Number of transport connections
o Connection capability, such as bandwidth, etc.
o Allowed/supported connection QoS policy (or congestion control
policy)
Doria, et al. Standards Track [Page 34]
RFC 5810 ForCES March 2010
6. Message Encapsulation
All PL PDUs start with a common header Section 6.1 followed by one or
more TLVs Section 6.2, which may nest other TLVs Section 6.2.1. All
fields are in network byte order.
6.1. Common Header
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|version| rsvd | Message Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Source ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Destination ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Correlator[63:32] |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Correlator[31:0] |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Flags |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 10: Common Header
The message is 32-bit aligned.
Version (4 bits):
Version number. Current version is 1.
rsvd (4 bits):
Unused at this point. A receiver should not interpret this field.
Senders MUST set it to zero and receivers MUST ignore this field.
Message Type (8 bits):
Commands are defined in Section 7.
Length (16 bits):
length of header + the rest of the message in DWORDS (4-byte
increments).
Source ID (32 bits):
Doria, et al. Standards Track [Page 35]
RFC 5810 ForCES March 2010
Dest ID (32 bits):
* Each of the source and destination IDs are 32-bit IDs that are
unique NE-wide and that identify the termination points of a
ForCES PL message.
* IDs allow multi/broad/unicast addressing with the following
approach:
a. A split address space is used to distinguish FEs from CEs.
Even though in a large NE there are typically two or more
orders of magnitude of more FEs than CEs, the address
space is split uniformly for simplicity.
b. The address space allows up to 2^30 (over a billion) CEs
and the same amount of FEs.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|TS | sub-ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 11: ForCES ID Format
c. The 2 most significant bits called Type Switch (TS) are
used to split the ID space as follows:
TS Corresponding ID range Assignment
-- ---------------------- ----------
0b00 0x00000000 to 0x3FFFFFFF FE IDs (2^30)
0b01 0x40000000 to 0x7FFFFFFF CE IDs (2^30)
0b10 0x80000000 to 0xBFFFFFFF reserved
0b11 0xC0000000 to 0xFFFFFFEF multicast IDs (2^30 - 16)
0b11 0xFFFFFFF0 to 0xFFFFFFFC reserved
0b11 0xFFFFFFFD all CEs broadcast
0b11 0xFFFFFFFE all FEs broadcast
0b11 0xFFFFFFFF all FEs and CEs (NE) broadcast
Figure 12: Type Switch ID Space
* Multicast or broadcast IDs are used to group endpoints (such
as CEs and FEs). As an example, one could group FEs in some
functional group, by assigning a multicast ID. Likewise,
subgroups of CEs that act, for instance, in a back-up mode may
be assigned a multicast ID to hide them from the FE.
Doria, et al. Standards Track [Page 36]
RFC 5810 ForCES March 2010
+ Multicast IDs can be used for both source or destination
IDs.
+ Broadcast IDs can be used only for destination IDs.
* This document does not discuss how a particular multicast ID
is associated to a given group though it could be done via
configuration process. The list of IDs an FE owns or is part
of are listed on the FE Object LFB.
Correlator (64 bits):
This field is set by the CE to correlate ForCES Request messages
with the corresponding Response messages from the FE.
Essentially, it is a cookie. The correlator is handled
transparently by the FE, i.e., for a particular Request message
the FE MUST assign the same correlator value in the corresponding
Response message. In the case where the message from the CE does
not elicit a response, this field may not be useful.
The correlator field could be used in many implementations in
specific ways by the CE. For example, the CE could split the
correlator into a 32-bit transactional identifier and 32-bit
message sequence identifier. Another example is a 64-bit pointer
to a context block. All such implementation-specific uses of the
correlator are outside the scope of this specification.
It should be noted that the correlator is transmitted on the
network as if it were a 64-bit unsigned integer with the leftmost
or most significant octet (bits 63-56) transmitted first.
Whenever the correlator field is not relevant, because no message
is expected, the correlator field is set to 0.
Flags (32 bits):
Identified so far:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | | | | | | |
|ACK| Pri |Rsr |EM |A|TP | Reserved |
| | | vd. | |T| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 13: Header Flags
- ACK: ACK indicator (2 bits)
Doria, et al. Standards Track [Page 37]
RFC 5810 ForCES March 2010
The ACK indicator flag is only used by the CE when sending a Config
message (Section 7.6.1) or an HB message (Section 7.10) to indicate
to the message receiver whether or not a response is required by the
sender. Note that for all other messages than the Config message or
the HB message this flag MUST be ignored.
The flag values are defined as follows:
'NoACK' (0b00) - to indicate that the message receiver MUST NOT
send any Response message back to this message sender.
'SuccessACK'(0b01) - to indicate that the message receiver MUST
send a Response message back only when the message has been
successfully processed by the receiver.
'FailureACK'(0b10) - to indicate that the message receiver MUST
send a Response message back only when there is failure by the
receiver in processing (executing) the message. In other words,
if the message can be processed successfully, the sender will not
expect any response from the receiver.
'AlwaysACK' (0b11) - to indicate that the message receiver MUST
send a Response message.
Note that in above definitions, the term success implies a complete
execution without any failure of the message. Anything else than a
complete successful execution is defined as a failure for the message
processing. As a result, for the execution modes (defined in
Section 4.3.1.1) like execute-all-or-none, execute-until-failure, and
continue-execute-on-failure, if any single operation among several
operations in the same message fails, it will be treated as a failure
and result in a response if the ACK indicator has been set to
'FailureACK' or 'AlwaysACK'.
Also note that, other than in Config and HB messages, requirements
for responses of messages are all given in a default way rather than
by ACK flags. The default requirements of these messages and the
expected responses are summarized below. Detailed descriptions can
be found in the individual message definitions:
+ Association Setup message always expects a response.
+ Association Teardown Message, and Packet Redirect
message, never expect responses.
+ Query message always expects a response.
+ Response message never expects further responses.
Doria, et al. Standards Track [Page 38]
RFC 5810 ForCES March 2010
- Pri: Priority (3 bits)
ForCES protocol defines 8 different levels of priority (0-7). The
priority level can be used to distinguish between different protocol
message types as well as between the same message type. The higher
the priority value, the more important the PDU is. For example, the
REDIRECT packet message could have different priorities to
distinguish between routing protocol packets and ARP packets being
redirected from FE to CE. The normal priority level is 1. The
different priorities imply messages could be re-ordered; however,
re-ordering is undesirable when it comes to a set of messages within
a transaction and caution should be exercised to avoid this.
- EM: Execution Mode (2 bits)
There are 3 execution modes; refer to Section 4.3.1.1 for details.
Reserved..................... (0b00)
`execute-all-or-none` ....... (0b01)
`execute-until-failure` ..... (0b10)
`continue-execute-on-failure` (0b11)
- AT: Atomic Transaction (1 bit)
This flag indicates if the message is a stand-alone message or one of
multiple messages that belong to 2PC transaction operations. See
Section 4.3.1.2.2 for details.
Stand-alone message ......... (0b0)
2PC transaction message ..... (0b1)
- TP: Transaction Phase (2 bits)
A message from the CE to the FE within a transaction could be
indicative of the different phases the transaction is in. Refer to
Section 4.3.1.2.2 for details.
SOT (start of transaction) ..... (0b00)
MOT (middle of transaction) .... (0b01)
EOT (end of transaction) ........(0b10)
ABT (abort) .....................(0b11)
Doria, et al. Standards Track [Page 39]
RFC 5810 ForCES March 2010
6.2. Type Length Value (TLV) Structuring
TLVs are extensively used by the ForCES protocol. TLVs have some
very nice properties that make them a good candidate for encoding the
XML definitions of the LFB class model. These are:
o Providing for binary type-value encoding that is close to the XML
string tag-value scheme.
o Allowing for fast generalized binary-parsing functions.
o Allowing for forward and backward tag compatibility. This is
equivalent to the XML approach, i.e., old applications can ignore
new TLVs and newer applications can ignore older TLVs.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| TLV Type | TLV Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value (Essentially the TLV Data) |
~ ~
~ ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 14: TLV Representation
TLV Type (16):
The TLV type field is 2 octets, and semantically indicates the type
of data encapsulated within the TLV.
TLV Length (16):
The TLV length field is 2 octets, and includes the length of the TLV
type (2 octets), TLV Length (2 octets), and the length of the TLV
data found in the value field, in octets. Note that this length is
the actual length of the value, before any padding for alignment is
added.
TLV Value (variable):
The TLV value field carries the data. For extensibility, the TLV
value may in fact be a TLV. Padding is required when the length is
not a multiple of 32 bits, and is the minimum number of octets
required to bring the TLV to a multiple of 32 bits. The length of
the value before padding is indicated by the TLV Length field.
Doria, et al. Standards Track [Page 40]
RFC 5810 ForCES March 2010
Note: The value field could be empty, which implies the minimal
length a TLV could be is 4 (length of "T" field and length of "L"
field).
6.2.1. Nested TLVs
TLV values can be other TLVs. This provides the benefits of protocol
flexibility (being able to add new extensions by introducing new TLVs
when needed). The nesting feature also allows for a conceptual
optimization with the XML LFB definitions to binary PL representation
(represented by nested TLVs).
6.2.2. Scope of the T in TLV
There are two global name scopes for the "Type" in the TLV. The
first name scope is for OPER-TLVs and is defined in A.4 whereas the
second name scope is outside OPER-TLVs and is defined in section A.2.
6.3. ILV
The ILV is a slight variation of the TLV. This sets the type ("T")
to be a 32-bit local index that refers to a ForCES component ID
(refer to Section 6.4.1).
The ILV length field is a 4-octet integer, and includes the length of
the ILV type (4 octets), ILV Length (4 octets), and the length of the
ILV data found in the value field, in octets. Note that, as in the
case of the TLV, this length is the actual length of the value,
before any padding for alignment is added.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Identifier |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Value |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 15: ILV Representation
It should be noted that the "I" values are of local scope and are
defined by the data declarations from the LFB definition. Refer to
Section 7.1.8 for discussions on usage of ILVs.
Doria, et al. Standards Track [Page 41]
RFC 5810 ForCES March 2010
6.4. Important Protocol Encapsulations
In this section, we review a few encapsulation concepts that are used
by the ForCES protocol for its operations.
We briefly re-introduce two concepts, paths, and keys, from the
ForCES model [RFC5812] in order to provide context. The reader is
referred to [RFC5812] for a lot of the finer details.
For readability reasons, we introduce the encapsulation schemes that
are used to carry content in a protocol message, namely, FULLDATA-
TLV, SPARSEDATA-TLV, and RESULT-TLV.
6.4.1. Paths
The ForCES model [RFC5812] defines an XML-based language that allows
for a formal definition of LFBs. This is similar to the relationship
between ASN.1 and SNMP MIB definition (MIB being analogous to the LFB
and ASN.1 being analogous to the XML model language). Any entity
that the CE configures on an FE MUST be formally defined in an LFB.
These entities could be scalars (e.g., a 32-bit IPv4 address) or
vectors (such as a nexthop table). Each entity within the LFB is
given a numeric 32-bit identifier known as a "component id". This
scheme allows the component to be "addressed" in a protocol
construct.
These addressable entities could be hierarchical (e.g., a table
column or a cell within a table row). In order to address
hierarchical data, the concept of a path is introduced by the model
[RFC5812]. A path is a series of 32-bit component IDs that are
typically presented in a dot-notation (e.g., 1.2.3.4). Section 7
formally defines how paths are used to reference data that is being
encapsulated within a protocol message.
6.4.2. Keys
The ForCES model [RFC5812] defines two ways to address table rows.
The standard/common mechanism is to allow table rows to be referenced
by a 32-bit index. The secondary mechanism is via keys that allow
for content addressing. An example key is a multi-field content key
that uses the IP address and prefix length to uniquely reference an
IPv4 routing table row. In essence, while the common scheme to
address a table row is via its table index, a table row's path could
be derived from a key. The KEYINFO-TLV (Section 7) is used to carry
the data that is used to do the lookup.
Doria, et al. Standards Track [Page 42]
RFC 5810 ForCES March 2010
6.4.3. DATA TLVs
Data from or to the FE is carried in two types of TLVs: FULLDATA-TLV
and SPARSEDATA-TLV. Responses to operations executed by the FE are
carried in RESULT-TLVs.
In FULLDATA-TLV, the data is encoded in such a way that a receiver of
such data, by virtue of being armed with knowledge of the path and
the LFB definition, can infer or correlate the TLV "Value" contents.
This is essentially an optimization that helps reduce the amount of
description required for the transported data in the protocol
grammar. Refer to Appendix C for an example of FULLDATA-TLVs.
A number of operations in ForCES will need to reference optional data
within larger structures. The SPARSEDATA-TLV encoding is provided to
make it easier to encapsulate optionally appearing data components.
Refer to Appendix C for an example of SPARSEDATA-TLV.
RESULT-TLVs carry responses back from the FE based on a config issued
by the CE. Refer to Appendix C for examples of RESULT-TLVs and
Section 7.1.7 for layout.
6.4.4. Addressing LFB Entities
Section 6.4.1 and Section 6.4.2 discuss how to target an entity
within an LFB. However, the addressing mechanism used requires that
an LFB type and instance are selected first. The LFB selector is
used to select an LFB type and instance being targeted. Section 7
goes into more details; for our purpose, we illustrate this concept
using Figure 16 below. More examples of layouts can be found reading
further into the text (example: Figure 22).
Doria, et al. Standards Track [Page 43]
RFC 5810 ForCES March 2010
main hdr (Message type: example "config")
|
|
|
+- T = LFBselect
|
+-- LFBCLASSID (unique per LFB defined)
|
|
+-- LFBInstance (runtime configuration)
|
+-- T = An operation TLV describes what we do to an entity
| //Refer to the OPER-TLV values enumerated below
| //the TLVs that can be used for operations
|
|
+--+-- one or more path encodings to target an entity
| // Refer to the discussion on keys and paths
|
|
+-- The associated data, if any, for the entity
// Refer to discussion on FULL/SPARSE DATA TLVs
Figure 16: Entity Addressing
7. Protocol Construction
A protocol layer PDU consists of a common header (defined in
Section 6.1 ) and a message body. The common header is followed by a
message-type-specific message body. Each message body is formed from
one or more top-level TLVs. A top-level TLV may contain one or more
sub-TLVs; these sub-TLVs are described in this document as OPER-TLVs,
because they describe an operation to be done.
Doria, et al. Standards Track [Page 44]
RFC 5810 ForCES March 2010
+-------------+---------------+---------------------+---------------+
| Message | Top-Level TLV | OPER-TLV(s) | Reference |
| Name | | | |
+-------------+---------------+---------------------+---------------+
| Association | (LFBselect)* | REPORT | Section 7.5.1 |
| Setup | | | |
| Association | ASRresult-TLV | none | Section 7.5.2 |
| Setup | | | |
| Response | | | |
| Association | ASTreason-TLV | none | Section 7.5.3 |
| Teardown | | | |
| Config | (LFBselect)+ | (SET | SET-PROP | | Section 7.6.1 |
| | | DEL | COMMIT | | |
| | | TRCOMP)+ | |
| Config | (LFBselect)+ | (SET-RESPONSE | | Section 7.6.2 |
| Response | | SET-PROP-RESPONSE | | |
| | | DEL-RESPONSE | | |
| | | COMMIT-RESPONSE)+ | |
| Query | (LFBselect)+ | (GET | GET-PROP)+ | Section 7.7.1 |
| Query | (LFBselect)+ | (GET-RESPONSE | | Section 7.7.2 |
| Response | | GET-PROP-RESPONSE)+ | |
| Event | LFBselect | REPORT | Section 7.8 |
| Notifi- | | | |
| cation | | | |
| Packet | REDIRECT-TLV | none | Section 7.9 |
| Redirect | | | |
| Heartbeat | none | none | Section 7.10 |
+-------------+---------------+---------------------+---------------+
Table 1
The different messages are illustrated in Table 1. The different
message type numerical values are defined in Appendix A.1. All the
TLV values are defined in Appendix A.2.
An LFBselect TLV (refer to Section 7.1.5) contains the LFB Classid
and LFB instance being referenced as well as the OPER-TLV(s) being
applied to that reference.
Each type of OPER-TLV is constrained as to how it describes the paths
and selectors of interest. The following BNF describes the basic
structure of an OPER-TLV and Table 2 gives the details for each type.
Doria, et al. Standards Track [Page 45]
RFC 5810 ForCES March 2010
OPER-TLV := 1*PATH-DATA-TLV
PATH-DATA-TLV := PATH [DATA]
PATH := flags IDcount IDs [SELECTOR]
SELECTOR := KEYINFO-TLV
DATA := FULLDATA-TLV / SPARSEDATA-TLV / RESULT-TLV /
1*PATH-DATA-TLV
KEYINFO-TLV := KeyID FULLDATA-TLV
FULLDATA-TLV := encoded data component which may nest
further FULLDATA-TLVs
SPARSEDATA-TLV := encoded data that may have optionally
appearing components
RESULT-TLV := Holds result code and optional FULLDATA-TLV
Figure 17: BNF of OPER-TLV
o PATH-DATA-TLV identifies the exact component targeted and may have
zero or more paths associated with it. The last PATH-DATA-TLV in
the case of nesting of paths via the DATA construct in the case of
SET, SET-PROP requests, and GET-RESPONSE/GET-PROP-RESPONSE is
terminated by encoded data or response in the form of either
FULLDATA-TLV or SPARSEDATA-TLV or RESULT-TLV.
o PATH provides the path to the data being referenced.
* flags (16 bits) are used to further refine the operation to be
applied on the path. More on these later.
* IDcount (16 bits): count of 32-bit IDs
* IDs: zero or more 32-bit IDs (whose count is given by IDcount)
defining the main path. Depending on the flags, IDs could be
field IDs only or a mix of field and dynamic IDs. Zero is used
for the special case of using the entirety of the containing
context as the result of the path.
o SELECTOR is an optional construct that further defines the PATH.
Currently, the only defined selector is the KEYINFO-TLV, used for
selecting an array entry by the value of a key field. The
presence of a SELECTOR is correct only when the flags also
indicate its presence.
o A KEYINFO-TLV contains information used in content keying.
* A 32-bit KeyID is used in a KEYINFO-TLV. It indicates which
key for the current array is being used as the content key for
array entry selection.
Doria, et al. Standards Track [Page 46]
RFC 5810 ForCES March 2010
* The key's data is the data to look for in the array, in the
fields identified by the key field. The information is encoded
according to the rules for the contents of a FULLDATA-TLV, and
represents the field or fields that make up the key identified
by the KeyID.
o DATA may contain a FULLDATA-TLV, SPARSEDATA-TLV, a RESULT-TLV, or
1 or more further PATH-DATA selections. FULLDATA-TLV and
SPARSEDATA-TLV are only allowed on SET or SET-PROP requests, or on
responses that return content information (GET-RESPONSE, for
example). PATH-DATA may be included to extend the path on any
request.
* Note: Nested PATH-DATA-TLVs are supported as an efficiency
measure to permit common subexpression extraction.
* FULLDATA-TLV and SPARSEDATA-TLV contain "the data" whose path
has been selected by the PATH. Refer to Section 7.1 for
details.
* The following table summarizes the applicability and
restrictions of the FULL/SPARSEDATA-TLVs and the RESULT-TLV to
the OPER-TLVs.
+-------------------+-------------------------------+---------------+
| OPER-TLV | DATA TLV | RESULT-TLV |
+-------------------+-------------------------------+---------------+
| SET | | none |
| SET-PROP | (FULLDATA-TLV | | none |
| | SPARSEDATA-TLV)+ | |
| SET-RESPONSE | none | (RESULT-TLV)+ |
| SET-PROP-RESPONSE | none | (RESULT-TLV)+ |
| DEL | | none |
| DEL-RESPONSE | none | (RESULT-TLV)+ |
| GET | none | none |
| GET-PROP | none | none |
| GET-RESPONSE | (FULLDATA-TLV)+ | (RESULT-TLV)* |
| GET-PROP-RESPONSE | (FULLDATA-TLV)+ | (RESULT-TLV)* |
| REPORT | (FULLDATA-TLV)+ | none |
| COMMIT | none | none |
| COMMIT-RESPONSE | none | (RESULT-TLV)+ |
| TRCOMP | none | none |
+-------------------+-------------------------------+---------------+
Table 2
Doria, et al. Standards Track [Page 47]
RFC 5810 ForCES March 2010
o RESULT-TLV contains the indication of whether the individual SET
or SET-PROP succeeded. RESULT-TLV is included on the assumption
that individual parts of a SET request can succeed or fail
separately.
In summary, this approach has the following characteristics:
o There can be one or more LFB class ID and instance ID combinations
targeted in a message (batch).
o There can one or more operations on an addressed LFB class ID/
instance ID combination (batch).
o There can be one or more path targets per operation (batch).
o Paths may have zero or more data values associated (flexibility
and operation specific).
It should be noted that the above is optimized for the case of a
single LFB class ID and instance ID targeting. To target multiple
instances within the same class, multiple LFBselects are needed.
7.1. Discussion on Encoding
Section 6.4.3 discusses the two types of DATA encodings (FULLDATA-TLV
and SPARSEDATA-TLV) and the justifications for their existence. In
this section, we explain how they are encoded.
7.1.1. Data Packing Rules
The scheme for encoding data used in this document adheres to the
following rules:
o The Value ("V" of TLV) of FULLDATA-TLV will contain the data being
transported. This data will be as was described in the LFB
definition.
o Variable-sized data within a FULLDATA-TLV will be encapsulated
inside another FULLDATA-TLV inside the V of the outer TLV. For an
example of such a setup, refer to Appendices C and D.
o In the case of FULLDATA-TLVs:
* When a table is referred to in the PATH (IDs) of a PATH-DATA-
TLV, then the FULLDATA-TLV's "V" will contain that table's row
content prefixed by its 32-bit index/subscript. On the other
Doria, et al. Standards Track [Page 48]
RFC 5810 ForCES March 2010
hand, the PATH may contain an index pointing to a row in table;
in such a case, the FULLDATA-TLV's "V" will only contain the
content with the index in order to avoid ambiguity.
7.1.2. Path Flags
Only bit 0, the SELECTOR Bit, is currently used in the path flags as
illustrated in Figure 18.
0 1
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| | |
|S| Reserved |
| | |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 18: Path Flags
The semantics of the flag are defined as follows:
o SELECTOR Bit: F_SELKEY(set to 1) indicates that a KEY Selector is
present following this path information, and should be considered
in evaluating the path content.
7.1.3. Relation of Operational Flags with Global Message Flags
Global flags, such as the execution mode and the atomicity indicators
defined in the header, apply to all operations in a message. Global
flags provide semantics that are orthogonal to those provided by the
operational flags, such as the flags defined in path-data. The scope
of operational flags is restricted to the operation.
7.1.4. Content Path Selection
The KEYINFO-TLV describes the KEY as well as associated KEY data.
KEYs, used for content searches, are restricted and described in the
LFB definition.
7.1.5. LFBselect-TLV
The LFBselect TLV is an instance of a TLV as defined in Section 6.2.
The definition is as follows:
Doria, et al. Standards Track [Page 49]
RFC 5810 ForCES March 2010
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = LFBselect | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LFB Class ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| LFB Instance ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPER-TLV |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| OPER-TLV |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 19: PL PDU Layout
Type:
The type of the TLV is "LFBselect"
Length:
Length of the TLV including the T and L fields, in octets.
LFB Class ID:
This field uniquely recognizes the LFB class/type.
LFB Instance ID:
This field uniquely identifies the LFB instance.
OPER-TLV:
It describes an operation nested in the LFBselect TLV. Note that
usually there SHOULD be at least one OPER-TLV present for an LFB
select TLV.
7.1.6. OPER-TLV
The OPER-TLV is a place holder in the grammar for TLVs that define
operations. The different types are defined in Table 3, below.
Doria, et al. Standards Track [Page 50]
RFC 5810 ForCES March 2010
+-------------------+--------+--------------------------------------+
| OPER-TLV | TLV | Comments |
| | "Type" | |
+-------------------+--------+--------------------------------------+
| SET | 0x0001 | From CE to FE. Used to create or |
| | | add or update components |
| SET-PROP | 0x0002 | From CE to FE. Used to create or |
| | | add or update component properties |
| SET-RESPONSE | 0x0003 | From FE to CE. Used to carry |
| | | response of a SET |
| SET-PROP-RESPONSE | 0x0004 | From FE to CE. Used to carry |
| | | response of a SET-PROP |
| DEL | 0x0005 | From CE to FE. Used to delete or |
| | | remove an component |
| DEL-RESPONSE | 0x0006 | From FE to CE. Used to carry |
| | | response of a DEL |
| GET | 0x0007 | From CE to FE. Used to retrieve an |
| | | component |
| GET-PROP | 0x0008 | From CE to FE. Used to retrieve an |
| | | component property |
| GET-RESPONSE | 0x0009 | From FE to CE. Used to carry |
| | | response of a GET |
| GET-PROP-RESPONSE | 0x000A | From FE to CE. Used to carry |
| | | response of a GET-PROP |
| REPORT | 0x000B | From FE to CE. Used to carry an |
| | | asynchronous event |
| COMMIT | 0x000C | From CE to FE. Used to issue a |
| | | commit in a 2PC transaction |
| COMMIT-RESPONSE | 0x000D | From FE to CE. Used to confirm a |
| | | commit in a 2PC transaction |
| TRCOMP | 0x000E | From CE to FE. Used to indicate |
| | | NE-wide success of 2PC transaction |
+-------------------+--------+--------------------------------------+
Table 3
Different messages use OPER-TLV and define how they are used (refer
to Table 1 and Table 2).
SET, SET-PROP, and GET/GET-PROP requests are issued by the CE and do
not carry RESULT-TLVs. On the other hand, SET-RESPONSE, SET-PROP-
RESPONSE, and GET-RESPONSE/GET-PROP-RESPONSE carry RESULT-TLVs.
A GET-RESPONSE in response to a successful GET will have FULLDATA-
TLVs added to the leaf paths to carry the requested data. For GET
operations that fail, instead of the FULLDATA-TLV there will be a
RESULT-TLV.
Doria, et al. Standards Track [Page 51]
RFC 5810 ForCES March 2010
For a SET-RESPONSE/SET-PROP-RESPONSE, each FULLDATA-TLV or
SPARSEDATA-TLV in the original request will be replaced with a
RESULT-TLV in the response. If the request set the FailureACK flag,
then only those items that failed will appear in the response. If
the request was for AlwaysACK, then all components of the request
will appear in the response with RESULT-TLVs.
Note that if a SET/SET-PROP request with a structure in a FULLDATA-
TLV is issued, and some field in the structure is invalid, the FE
will not attempt to indicate which field was invalid, but rather will
indicate that the operation failed. Note further that if there are
multiple errors in a single leaf PATH-DATA/FULLDATA-TLB, the FE can
select which error it chooses to return. So if a FULLDATA-TLV for a
SET/SET-PROP of a structure attempts to write one field that is read
only, and attempts to set another field to an invalid value, the FE
can return indication of either error.
A SET/SET-PROP operation on a variable-length component with a length
of 0 for the item is not the same as deleting it. If the CE wishes
to delete, then the DEL operation should be used whether the path
refers to an array component or an optional structure component.
7.1.7. RESULT TLV
The RESULT-TLV is an instance of TLV defined in Section 6.2. The
definition is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = RESULT-TLV | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Result Value | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 20: RESULT-TLV
Doria, et al. Standards Track [Page 52]
RFC 5810 ForCES March 2010
Defined Result Values
+-----------------------------+-----------+-------------------------+
| Result Value | Value | Definition |
+-----------------------------+-----------+-------------------------+
| E_SUCCESS | 0x00 | Success |
| E_INVALID_HEADER | 0x01 | Unspecified error with |
| | | header. |
| E_LENGTH_MISMATCH | 0x02 | Header length field |
| | | does not match actual |
| | | packet length. |
| E_VERSION_MISMATCH | 0x03 | Unresolvable mismatch |
| | | in versions. |
| E_INVALID_DESTINATION_PID | 0x04 | Destination PID is |
| | | invalid for the message |
| | | receiver. |
| E_LFB_UNKNOWN | 0x05 | LFB Class ID is not |
| | | known by receiver. |
| E_LFB_NOT_FOUND | 0x06 | LFB Class ID is known |
| | | by receiver but not |
| | | currently in use. |
| E_LFB_INSTANCE_ID_NOT_FOUND | 0x07 | LFB Class ID is known |
| | | but the specified |
| | | instance of that class |
| | | does not exist. |
| E_INVALID_PATH | 0x08 | The specified path is |
| | | impossible. |
| E_COMPONENT_DOES_NOT_EXIST | 0x09 | The specified path is |
| | | possible but the |
| | | component does not |
| | | exist (e.g., attempt to |
| | | modify a table row that |
| | | has not been created). |
| E_EXISTS | 0x0A | The specified object |
| | | exists but it cannot |
| | | exist for the operation |
| | | to succeed (e.g., |
| | | attempt to add an |
| | | existing LFB instance |
| | | or array subscript). |
| E_NOT_FOUND | 0x0B | The specified object |
| | | does not exist but it |
| | | MUST exist for the |
| | | operation to succeed |
| | | (e.g., attempt to |
| | | delete a non-existing |
| | | LFB instance or array |
| | | subscript). |
Doria, et al. Standards Track [Page 53]
RFC 5810 ForCES March 2010
| E_READ_ONLY | 0x0C | Attempt to modify a |
| | | read-only value. |
| E_INVALID_ARRAY_CREATION | 0x0D | Attempt to create an |
| | | array with an unallowed |
| | | subscript. |
| E_VALUE_OUT_OF_RANGE | 0x0E | Attempt to set a |
| | | parameter to a value |
| | | outside of its |
| | | allowable range. |
| E_CONTENTS_TOO_LONG | 0x0D | Attempt to write |
| | | contents larger than |
| | | the target object space |
| | | (i.e., exceeding a |
| | | buffer). |
| E_INVALID_PARAMETERS | 0x10 | Any other error with |
| | | data parameters. |
| E_INVALID_MESSAGE_TYPE | 0x11 | Message type is not |
| | | acceptable. |
| E_INVALID_FLAGS | 0x12 | Message flags are not |
| | | acceptable for the |
| | | given message type. |
| E_INVALID_TLV | 0x13 | A TLV is not acceptable |
| | | for the given message |
| | | type. |
| E_EVENT_ERROR | 0x14 | Unspecified error while |
| | | handling an event. |
| E_NOT_SUPPORTED | 0x15 | Attempt to perform a |
| | | valid ForCES operation |
| | | that is unsupported by |
| | | the message receiver. |
| E_MEMORY_ERROR | 0x16 | A memory error occurred |
| | | while processing a |
| | | message (no error |
| | | detected in the message |
| | | itself). |
| E_INTERNAL_ERROR | 0x17 | An unspecified error |
| | | occurred while |
| | | processing a message |
| | | (no error detected in |
| | | the message itself). |
| - | 0x18-0xFE | Reserved |
| E_UNSPECIFIED_ERROR | 0xFF | Unspecified error (for |
| | | when the FE cannot |
| | | decide what went |
| | | wrong). |
+-----------------------------+-----------+-------------------------+
Table 4
Doria, et al. Standards Track [Page 54]
RFC 5810 ForCES March 2010
7.1.8. DATA TLV
A FULLDATA-TLV has "T"= FULLDATA-TLV and a 16-bit length followed by
the data value/contents. Likewise, a SPARSEDATA-TLV has "T" =
SPARSEDATA-TLV, a 16-bit length, followed by the data value/contents.
In the case of the SPARSEDATA-TLV, each component in the Value part
of the TLV will be further encapsulated in an ILV.
Below are the encoding rules for the FULLDATA-TLV and SPARSEDATA-
TLVs. Appendix C is very useful in illustrating these rules:
1. Both ILVs and TLVs MUST be 32-bit aligned. Any padding bits used
for the alignment MUST be zero on transmission and MUST be
ignored upon reception.
2. FULLDATA-TLVs may be used at a particular path only if every
component at that path level is present. In example 1(c) of
Appendix C, this concept is illustrated by the presence of all
components of the structure S in the FULLDATA-TLV encoding. This
requirement holds regardless of whether the fields are fixed or
variable length, mandatory or optional.
* If a FULLDATA-TLV is used, the encoder MUST lay out data for
each component in the same order in which the data was
defined in the LFB specification. This ensures the decoder
is able to retrieve the data. To use the example 1 again in
Appendix C, this implies the encoder/decoder is assumed to
have knowledge of how structure S is laid out in the
definition.
* In the case of a SPARSEDATA-TLV, it does not need to be
ordered since the "I" in the ILV uniquely identifies the
component. Examples 1(a) and 1(b) in Appendix C illustrate
the power of SPARSEDATA-TLV encoding.
3. Inside a FULLDATA-TLV
* The values for atomic, fixed-length fields are given without
any TLV encapsulation.
* The values for atomic, variable-length fields are given
inside FULLDATA-TLVs.
* The values for arrays are in the form of index/subscript,
followed by value as stated in "Data Packing Rules"
(Section 7.1.1) and demonstrated by the examples in the
appendices.
Doria, et al. Standards Track [Page 55]
RFC 5810 ForCES March 2010
4. Inside a SPARSEDATA-TLV
* The values of all fields MUST be given with ILVs (32-bit
index, 32-bit length).
5. FULLDATA-TLVs cannot contain an ILV.
6. A FULLDATA-TLV can also contain a FULLDATA-TLV for variable-sized
components. The decoding disambiguation is assumed from rule #3
above.
7.1.9. SET and GET Relationship
It is expected that a GET-RESPONSE would satisfy the following:
o It would have exactly the same path definitions as those sent in
the GET. The only difference is that a GET-RESPONSE will contain
FULLDATA-TLVs.
o It should be possible to take the same GET-RESPONSE and convert
it to a SET successfully by merely changing the T in the
operational TLV.
o There are exceptions to this rule:
1. When a KEY selector is used with a path in a GET operation,
that selector is not returned in the GET-RESPONSE; instead,
the cooked result is returned. Refer to the examples using
KEYS to see this.
2. When dumping a whole table in a GET, the GET-RESPONSE that
merely edits the T to be SET will end up overwriting the
table.
7.2. Protocol Encoding Visualization
The figure below shows a general layout of the PL PDU. A main header
is followed by one or more LFB selections each of which may contain
one or more operations.
Doria, et al. Standards Track [Page 56]
RFC 5810 ForCES March 2010
main hdr (Config in this case)
|
|
+--- T = LFBselect
| |
| +-- LFBCLASSID
| |
| |
| +-- LFBInstance
| |
| +-- T = SET
| | |
| | +-- // one or more path targets
| | // with their data here to be added
| |
| +-- T = DEL
| . |
| . +-- // one or more path targets to be deleted
|
|
+--- T = LFBselect
| |
| +-- LFBCLASSID
| |
| |
| +-- LFBInstance
| |
| + -- T= SET
| | .
| | .
| + -- T= DEL
| | .
| | .
| |
| + -- T= SET
| | .
| | .
|
|
+--- T = LFBselect
|
+-- LFBCLASSID
|
+-- LFBInstance
.
.
.
Figure 21: PL PDU Logical Layout
Doria, et al. Standards Track [Page 57]
RFC 5810 ForCES March 2010
The figure below shows a more detailed example of the general layout
of the operation within a targeted LFB selection. The idea is to
show the different nesting levels a path could take to get to the
target path.
T = SET
| |
| +- T = Path-data
| |
| + -- flags
| + -- IDCount
| + -- IDs
| |
| +- T = Path-data
| |
| + -- flags
| + -- IDCount
| + -- IDs
| |
| +- T = Path-data
| |
| + -- flags
| + -- IDCount
| + -- IDs
| + -- T = KEYINFO-TLV
| | + -- KEY_ID
| | + -- KEY_DATA
| |
| + -- T = FULLDATA-TLV
| + -- data
|
|
T = SET
| |
| +- T = Path-data
| | |
| | + -- flags
| | + -- IDCount
| | + -- IDs
| | |
| | + -- T = FULLDATA-TLV
| | + -- data
| +- T = Path-data
| |
Doria, et al. Standards Track [Page 58]
RFC 5810 ForCES March 2010
| + -- flags
| + -- IDCount
| + -- IDs
| |
| + -- T = FULLDATA-TLV
| + -- data
T = DEL
|
+- T = Path-data
|
+ -- flags
+ -- IDCount
+ -- IDs
|
+- T = Path-data
|
+ -- flags
+ -- IDCount
+ -- IDs
|
+- T = Path-data
|
+ -- flags
+ -- IDCount
+ -- IDs
+ -- T = KEYINFO-TLV
| + -- KEY_ID
| + -- KEY_DATA
+- T = Path-data
|
+ -- flags
+ -- IDCount
+ -- IDs
Figure 22: Sample Operation Layout
Appendix D shows a more concise set of use cases on how the data
encoding is done.
7.3. Core ForCES LFBs
There are two LFBs that are used to control the operation of the
ForCES protocol and to interact with FEs and CEs:
o FE Protocol LFB
Doria, et al. Standards Track [Page 59]
RFC 5810 ForCES March 2010
o FE Object LFB
Although these LFBs have the same form and interface as other LFBs,
they are special in many respects. They have fixed well-known LFB
Class and Instance IDs. They are statically defined (no dynamic
instantiation allowed), and their status cannot be changed by the
protocol: any operation to change the state of such LFBs (for
instance, in order to disable the LFB) MUST result in an error.
Moreover, these LFBs MUST exist before the first ForCES message can
be sent or received. All components in these LFBs MUST have pre-
defined default values. Finally, these LFBs do not have input or
output ports and do not integrate into the intra-FE LFB topology.
7.3.1. FE Protocol LFB
The FE Protocol LFB is a logical entity in each FE that is used to
control the ForCES protocol. The FE Protocol LFB Class ID is
assigned the value 0x2. The FE Protocol LFB Instance ID is assigned
the value 0x1. There MUST be one and only one instance of the FE
Protocol LFB in an FE. The values of the components in the FE
Protocol LFB have pre-defined default values that are specified here.
Unless explicit changes are made to these values using Config
messages from the CE, these default values MUST be used for correct
operation of the protocol.
The formal definition of the FE Protocol Object LFB can be found in
Appendix B.
7.3.1.1. FE Protocol Capabilities
FE Protocol capabilities are read-only.
7.3.1.1.1. SupportableVersions
ForCES protocol version(s) supported by the FE.
7.3.1.1.2. FE Protocol Components
FE Protocol components (can be read and set).
7.3.1.1.2.1. CurrentRunningVersion
Current running version of the ForCES protocol.
Doria, et al. Standards Track [Page 60]
RFC 5810 ForCES March 2010
7.3.1.1.2.2. FEID
FE unicast ID.
7.3.1.1.2.3. MulticastFEIDs
FE multicast ID(s) list - This is a list of multicast IDs to which
the FE belongs. These IDs are configured by the CE.
7.3.1.1.2.4. CEHBPolicy
CE heartbeat policy - This policy, along with the parameter 'CE
Heartbeat Dead Interval (CE HDI)' as described below, defines the
operating parameters for the FE to check the CE liveness. The policy
values with meanings are listed as follows:
o 0 (default) - This policy specifies that the CE will send a
Heartbeat message to the FE(s) whenever the CE reaches a time
interval within which no other PL messages were sent from the CE
to the FE(s); refer to Section 4.3.3 and Section 7.10 for details.
The CE HDI component as described below is tied to this policy.
o 1 - The CE will not generate any HB messages. This actually means
that the CE does not want the FE to check the CE liveness.
o Others - Reserved.
7.3.1.1.2.5. CEHDI
CE Heartbeat Dead Interval (CE HDI) - The time interval the FE uses
to check the CE liveness. If FE has not received any messages from
CE within this time interval, FE deduces lost connectivity, which
implies that the CE is dead or the association to the CE is lost.
Default value is 30 s.
7.3.1.1.2.6. FEHBPolicy
FE heartbeat policy - This policy, along with the parameter 'FE
Heartbeat Interval (FE HI)', defines the operating parameters for how
the FE should behave so that the CE can deduce its liveness. The
policy values and the meanings are:
o 0 (default) - The FE should not generate any Heartbeat messages.
In this scenario, the CE is responsible for checking FE liveness
by setting the PL header ACK flag of the message it sends to
AlwaysACK. The FE responds to the CE whenever the CE sends such
Heartbeat Request messages. Refer to Section 7.10 and
Section 4.3.3 for details.
Doria, et al. Standards Track [Page 61]
RFC 5810 ForCES March 2010
o 1 - This policy specifies that the FE MUST actively send a
Heartbeat message if it reaches the time interval assigned by the
FE HI as long as no other messages were sent from the FE to the CE
during that interval as described in Section 4.3.3.
o Others - Reserved.
7.3.1.1.2.7. FEHI
FE Heartbeat Interval (FE HI) - The time interval the FE should use
to send HB as long as no other messages were sent from the FE to the
CE during that interval as described in Section 4.3.3. The default
value for an FE HI is 500 ms.
7.3.1.1.2.8. CEID
Primary CEID - The CEID with which the FE is associated.
7.3.1.1.2.9. LastCEID
Last Primary CEID - The CEID of the last CE with which the FE
associated. This CE ID is reported to the new Primary CEID.
7.3.1.1.2.10. BackupCEs
The list of backup CEs an FE can use as backups. Refer to Section 8
for details.
7.3.1.1.2.11. CEFailoverPolicy
CE failover policy - This specifies the behavior of the FE when the
association with the CE is lost. There is a very tight relation
between CE failover policy and Section 7.3.1.1.2.8,
Section 7.3.1.1.2.10, Section 7.3.1.1.2.12, and Section 8. When an
association is lost, depending on configuration, one of the policies
listed below is activated.
o 0 (default) - The FE should stop functioning immediately and
transition to FE OperDisable.
o 1 - The FE should continue running and do what it can even without
an associated CE. This basically requires that the FE support CE
Graceful restart (and defines such support in its capabilities).
If the CEFTI expires before the FE re-associates with either the
primary CEID (Section 7.3.1.1.2.8) or one of possibly several
backup CEs (Section 7.3.1.1.2.10), the FE will go operationally
down.
Doria, et al. Standards Track [Page 62]
RFC 5810 ForCES March 2010
o Others - Reserved.
7.3.1.1.2.12. CEFTI
CE Failover Timeout Interval (CEFTI) - The time interval associated
with the CE failover policy case '0' and '1'. The default value is
set to 300 seconds. Note that it is advisable to set the CEFTI value
much higher than the CE Heartbeat Dead Interval (CE HDI) since the
effect of expiring this parameter is devastating to the operation of
the FE.
7.3.1.1.2.13. FERestartPolicy
FE restart policy - This specifies the behavior of the FE during an
FE restart. The restart may be from an FE failure or other reasons
that have made the FE down and then need to restart. The values are
defined as follows:
o 0(default)- Restart the FE from scratch. In this case, the FE
should start from the pre-association phase.
o Others - Reserved for future use.
7.3.2. FE Object LFB
The FE Object LFB is a logical entity in each FE and contains
components relative to the FE itself, and not to the operation of the
ForCES protocol.
The formal definition of the FE Object LFB can be found in [RFC5812].
The model captures the high-level properties of the FE that the CE
needs to know to begin working with the FE. The class ID for this
LFB class is also assigned in [RFC5812]. The singular instance of
this class will always exist, and will always have instance ID 0x1
within its class. It is common, although not mandatory, for a CE to
fetch much of the component and capability information from this LFB
instance when the CE begins controlling the operation of the FE.
7.4. Semantics of Message Direction
Recall: The PL provides a master(CE)-slave(FE) relationship. The
LFBs reside at the FE and are controlled by CE.
When messages go from the CE, the LFB selector (class and instance)
refers to the destination LFB selection that resides in the FE.
When messages go from the FE to the CE, the LFB selector (class and
instance) refers to the source LFB selection that resides in the FE.
Doria, et al. Standards Track [Page 63]
RFC 5810 ForCES March 2010
7.5. Association Messages
The ForCES Association messages are used to establish and tear down
associations between FEs and CEs.
7.5.1. Association Setup Message
This message is sent by the FE to the CE to set up a ForCES
association between them.
Message transfer direction:
FE to CE
Message header:
The Message Type in the header is set to MessageType=
'AssociationSetup'. The ACK flag in the header MUST be ignored,
and the Association Setup message always expects to get a response
from the message receiver (CE), whether or not the setup is
successful. The correlator field in the header is set, so that FE
can correlate the response coming back from the CE correctly. The
FE may set the source ID to 0 in the header to request that the CE
should assign an FE ID for the FE in the Setup Response message.
Message body:
The Association Setup message body optionally consists of zero,
one, or two LFBselect TLVs, as described in Section 7.1.5. The
Association Setup message only operates on the FE Object and FE
Protocol LFBs; therefore, the LFB class ID in the LFBselect TLV
only points to these two kinds of LFBs.
The OPER-TLV in the LFBselect TLV is defined as a 'REPORT'
operation. More than one component may be announced in this
message using the REPORT operation to let the FE declare its
configuration parameters in an unsolicited manner. These may
contain components suggesting values such as the FE HB Interval or
the FEID. The OPER-TLV used is defined below.
Doria, et al. Standards Track [Page 64]
RFC 5810 ForCES March 2010
OPER-TLV for Association Setup:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = REPORT | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PATH-DATA-TLV for REPORT |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 23: OPER-TLV
Type:
Only one operation type is defined for the Association Setup
message:
Type = "REPORT" - This type of operation is for the FE to report
something to the CE.
PATH-DATA-TLV for REPORT:
This is generically a PATH-DATA-TLV format that has been defined
in Section 7 in the PATH-DATA BNF definition. The PATH-DATA-TLV
for the REPORT operation MAY contain FULLDATA-TLV(s) but SHALL NOT
contain any RESULT-TLV in the data format. The RESULT-TLV is
defined in Section 7.1.7 and the FULLDATA-TLV is defined in
Section 7.1.8.
Doria, et al. Standards Track [Page 65]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = Association Setup)
|
|
+--- T = LFBselect
| |
| +-- LFBCLASSID = FE object
| |
| |
| +-- LFBInstance = 0x1
|
+--- T = LFBselect
|
+-- LFBCLASSID = FE Protocol object
|
|
+-- LFBInstance = 0x1
|
+---OPER-TLV = REPORT
|
+-- Path-data to one or more components
Figure 24: PDU Format for Association Setup Message
7.5.2. Association Setup Response Message
This message is sent by the CE to the FE in response to the Setup
message. It indicates to the FE whether or not the setup is
successful, i.e., whether an association is established.
Message transfer direction:
CE to FE
Message header:
The Message Type in the header is set to MessageType=
'AssociationSetupResponse'. The ACK flag in the header MUST be
ignored, and the Setup Response message never expects to get any more
responses from the message receiver (FE). The destination ID in the
header will be set to the source ID in the corresponding Association
Setup message, unless that source ID was 0. If the corresponding
source ID was 0, then the CE will assign an FE ID value and use that
value for the destination ID.
Doria, et al. Standards Track [Page 66]
RFC 5810 ForCES March 2010
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = ASRresult | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Association Setup Result |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 25: ASResult OPER-TLV
Type (16 bits):
The type of the TLV is "ASResult".
Length (16 bits):
Length of the TLV including the T and L fields, in octets.
Association Setup result (32 bits):
This indicates whether the Setup message was successful or whether
the FE request was rejected by the CE. The defined values are:
0 = success
1 = FE ID invalid
2 = permission denied
Doria, et al. Standards Track [Page 67]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = Association Setup Response)
|
|
+--- T = ASResult-TLV
Figure 26: PDU Format for Association Setup Response Message
7.5.3. Association Teardown Message
This message can be sent by the FE or CE to any ForCES element to end
its ForCES association with that element.
Message transfer direction:
CE to FE, or FE to CE (or CE to CE)
Message Header:
The Message Type in the header is set to MessageType=
"AssociationTeardown". The ACK flag MUST be ignored. The correlator
field in the header MUST be set to zero and MUST be ignored by the
receiver.
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = ASTreason | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Teardown Reason |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 27: ASTreason-TLV
Type (16 bits):
The type of the TLV is "ASTreason".
Length (16 bits):
Length of the TLV including the T and L fields, in octets.
Teardown reason (32 bits):
This indicates the reason why the association is being terminated.
Several reason codes are defined as follows.
Doria, et al. Standards Track [Page 68]
RFC 5810 ForCES March 2010
0 - normal teardown by administrator
1 - error - loss of heartbeats
2 - error - out of bandwidth
3 - error - out of memory
4 - error - application crash
255 - error - other or unspecified
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = Association Teardown)
|
|
+--- T = ASTreason-TLV
Figure 28: PDU Format for Association Teardown Message
7.6. Configuration Messages
The ForCES Configuration messages are used by CE to configure the FEs
in a ForCES NE and report the results back to the CE.
7.6.1. Config Message
This message is sent by the CE to the FE to configure LFB components
in the FE. This message is also used by the CE to subscribe/
unsubscribe to LFB events.
As usual, a Config message is composed of a common header followed by
a message body that consists of one or more TLV data formats.
Detailed description of the message is as follows:
Message transfer direction:
CE to FE
Message header:
The Message Type in the header is set to MessageType= 'Config'. The
ACK flag in the header can be set to any value defined in
Section 6.1, to indicate whether or not a response from the FE is
expected by the message.
Doria, et al. Standards Track [Page 69]
RFC 5810 ForCES March 2010
OPER-TLV for Config:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PATH-DATA-TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 29: OPER-TLV for Config
Type:
The operation type for Config message. Two types of operations for
the Config message are defined:
Type = "SET" - This operation is to set LFB components
Type = "SET-PROP" - This operation is to set LFB component
properties.
Type = "DEL" - This operation is to delete some LFB components.
Type = "COMMIT" - This operation is sent to the FE to commit in a
2pc transaction. A COMMIT TLV is an empty TLV, i.e., it
has no "V"alue. In other words, there is a length of 4
(which is for the header only).
Type = "TRCOMP" - This operation is sent to the FE to mark the
success from an NE perspective of a 2pc transaction. A
TRCOMP TLV is an empty TLV, i.e., it has no "V"alue. In
other words, there is a length of 4 (which is for the
header only).
PATH-DATA-TLV:
This is generically a PATH-DATA-TLV format that has been defined in
Section 7 in the PATH-DATA-TLV BNF definition. The restriction on
the use of PATH-DATA-TLV for SET/SET-PROP operation is that it MUST
contain either FULLDATA-TLV or SPARSEDATA-TLV(s), but MUST NOT
contain any RESULT-TLV. The restriction on the use of PATH-DATA-TLV
for DEL operation is it MAY contain FULLDATA-TLV or
SPARSEDATA-TLV(s), but MUST NOT contain any RESULT-TLV. The
RESULT-TLV is defined in Section 7.1.7 and FULLDATA-TLVs and
SPARSEDATA-TLVs are defined in Section 7.1.8.
Doria, et al. Standards Track [Page 70]
RFC 5810 ForCES March 2010
Note: For Event subscription, the events will be defined by the
individual LFBs.
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = Config)
|
|
+--- T = LFBselect
. |
. +-- LFBCLASSID = target LFB class
. |
|
+-- LFBInstance = target LFB instance
|
|
+-- T = operation { SET }
| |
| +-- // one or more path targets
| // associated with FULLDATA-TLV or SPARSEDATA-TLV(s)
|
+-- T = operation { DEL }
| |
| +-- // one or more path targets
|
+-- T = operation { COMMIT } //A COMMIT TLV is an empty TLV
.
.
Figure 30: PDU Format for Configuration Message
7.6.2. Config Response Message
This message is sent by the FE to the CE in response to the Config
message. It indicates whether or not the Config was successful on
the FE and also gives a detailed response regarding the configuration
result of each component.
Message transfer direction:
FE to CE
Doria, et al. Standards Track [Page 71]
RFC 5810 ForCES March 2010
Message header:
The Message Type in the header is set to MessageType= 'Config
Response'. The ACK flag in the header is always ignored, and the
Config Response message never expects to get any further response
from the message receiver (CE).
OPER-TLV for Config Response:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PATH-DATA-TLV |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 31: OPER-TLV for Config Response
Type:
The operation type for Config Response message. Two types of
operations for the Config Response message are defined:
Type = "SET-RESPONSE" - This operation is for the response of the
SET operation of LFB components.
Type = "SET-PROP-RESPONSE" - This operation is for the response
of the SET-PROP operation of LFB component properties.
Type = "DEL-RESPONSE" - This operation is for the response of the
DELETE operation of LFB components.
Type = "COMMIT-RESPONSE" - This operation is sent to the CE to
confirm a commit success in a 2pc transaction. A
COMMIT-RESPONSE TLV MUST contain a RESULT-TLV indicating
success or failure.
PATH-DATA-TLV:
This is generically a PATH-DATA-TLV format that has been defined in
Section 7 in the PATH-DATA-TLV BNF definition. The restriction on
the use of PATH-DATA-TLV for SET-RESPONSE operation is that it MUST
contain RESULT-TLV(s). The restriction on the use of PATH-DATA-TLV
for DEL-RESPONSE operation is it also MUST contain RESULT-TLV(s).
The RESULT-TLV is defined in Section 7.1.7.
Doria, et al. Standards Track [Page 72]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = ConfigResponse)
|
|
+--- T = LFBselect
. |
. +-- LFBCLASSID = target LFB class
. |
|
+-- LFBInstance = target LFB instance
|
|
+-- T = operation { SET-RESPONSE }
| |
| +-- // one or more path targets
| // associated with FULL or SPARSEDATA-TLV(s)
|
+-- T = operation { DEL-RESPONSE }
| |
| +-- // one or more path targets
|
+-- T = operation { COMMIT-RESPONSE }
| |
| +-- RESULT-TLV
Figure 32: PDU Format for Config Response Message
7.7. Query Messages
The ForCES Query messages are used by the CE to query LFBs in the FE
for information like LFB components, capabilities, statistics, etc.
Query messages include the Query message and the Query Response
message.
7.7.1. Query Message
A Query message is composed of a common header and a message body
that consists of one or more TLV data formats. Detailed description
of the message is as follows:
Message transfer direction:
from CE to FE
Doria, et al. Standards Track [Page 73]
RFC 5810 ForCES March 2010
Message header:
The Message Type in the header is set to MessageType= 'Query'. The
ACK flag in the header is always ignored, and a full response for a
Query message is always expected. The Correlator field in the header
is set, so that the CE can locate the response back from FE
correctly.
OPER-TLV for Query:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = GET/GET-PROP | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PATH-DATA-TLV for GET/GET-PROP |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 33: TLV for Query
Type:
The operation type for query. Two operation types are defined:
Type = "GET" - This operation is to request to get LFB
components.
Type = "GET-PROP" - This operation is to request to get LFB
component properties.
PATH-DATA-TLV for GET/GET-PROP:
This is generically a PATH-DATA-TLV format that has been defined in
Section 7 in the PATH-DATA-TLV BNF definition. The restriction on
the use of PATH-DATA-TLV for GET/GET-PROP operation is it MUST NOT
contain any SPARSEDATA-TLV or FULLDATA- TLV and RESULT-TLV in the
data format.
Doria, et al. Standards Track [Page 74]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = Query)
|
|
+--- T = LFBselect
. |
. +-- LFBCLASSID = target LFB class
. |
|
+-- LFBInstance = target LFB instance
|
|
+-- T = operation { GET }
| |
| +-- // one or more path targets
|
+-- T = operation { GET }
. |
. +-- // one or more path targets
.
Figure 34: PDU Format for Query Message
7.7.2. Query Response Message
When receiving a Query message, the receiver should process the
message and come up with a query result. The receiver sends the
query result back to the message sender by use of the Query Response
message. The query result can be the information being queried if
the query operation is successful, or can also be error codes if the
query operation fails, indicating the reasons for the failure.
A Query Response message is also composed of a common header and a
message body consisting of one or more TLVs describing the query
result. Detailed description of the message is as follows:
Message transfer direction:
from FE to CE
Message header:
The Message Type in the header is set to MessageType=
'QueryResponse'. The ACK flag in the header is ignored. As a
response itself, the message does not expect a further response.
Doria, et al. Standards Track [Page 75]
RFC 5810 ForCES March 2010
OPER-TLV for Query Response:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
|Type = GET-RESPONSE/GET-PROP-RESPONSE| Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PATH-DATA-TLV for GET-RESPONSE/GET-PROP-RESPONSE |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 35: TLV for Query Response
Type:
The operation type for query response. One operation type is
defined:
Type = "GET-RESPONSE" - This operation is for the response of the
GET operation of LFB components.
Type = "GET-PROP-RESPONSE" - This operation is for the response
of the GET-PROP operation of LFB components.
PATH-DATA-TLV for GET-RESPONSE/GET-PROP-RESPONSE:
This is generically a PATH-DATA-TLV format that has been defined in
Section 7 in the PATH-DATA-TLV BNF definition. The PATH-DATA- TLV
for the GET-RESPONSE operation MAY contain SPARSEDATA-TLV,
FULLDATA-TLV, and/or RESULT-TLV(s) in the data encoding. The
RESULT-TLV is defined in Section 7.1.7 and the SPARSEDATA-TLVs and
FULLDATA-TLVs are defined in Section 7.1.8.
Doria, et al. Standards Track [Page 76]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = QueryResponse)
|
|
+--- T = LFBselect
. |
. +-- LFBCLASSID = target LFB class
. |
|
+-- LFBInstance = target LFB instance
|
|
+-- T = operation { GET-RESPONSE }
| |
| +-- // one or more path targets
|
+-- T = operation { GET-PROP-RESPONSE }
. |
. +-- // one or more path targets
.
Figure 36: PDU Format for Query Response Message
7.8. Event Notification Message
Event Notification message is used by the FE to asynchronously notify
the CE of events that happen in the FE.
All events that can be generated in an FE are subscribable by the CE.
The CE can subscribe to an event via a Config message with the SET-
PROP operation, where the included path specifies the event, as
defined by the LFB Library and described by the FE Model.
As usual, an Event Notification message is composed of a common
header and a message body that consists of one or more TLV data
formats. Detailed description of the message is as follows:
Message transfer direction:
FE to CE
Doria, et al. Standards Track [Page 77]
RFC 5810 ForCES March 2010
Message header:
The Message Type in the message header is set to
MessageType = 'EventNotification'. The ACK flag in the header MUST
be ignored by the CE, and the Event Notification message does not
expect any response from the receiver.
OPER-TLV for Event Notification:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = REPORT | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| PATH-DATA-TLV for REPORT |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 37: TLV for Event Notification
Type:
Only one operation type is defined for the Event Notification
message:
Type = "REPORT" - This type of operation is for the FE to report
something to the CE.
PATH-DATA-TLV for REPORT:
This is generically a PATH-DATA-TLV format that has been defined in
Section 7 in the PATH-DATA-TLV BNF definition. The PATH-DATA- TLV
for the REPORT operation MAY contain FULLDATA-TLV or
SPARSEDATA-TLV(s) but MUST NOT contain any RESULT-TLV in the data
format.
Doria, et al. Standards Track [Page 78]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = Event Notification)
|
|
+--- T = LFBselect
|
+-- LFBCLASSID = target LFB class
|
|
+-- LFBInstance = target LFB instance
|
|
+-- T = operation { REPORT }
| |
| +-- // one or more path targets
| // associated with FULL/SPARSE DATA TLV(s)
+-- T = operation { REPORT }
. |
. +-- // one or more path targets
. // associated with FULL/SPARSE DATA TLV(s)
Figure 38: PDU Format for Event Notification Message
7.9. Packet Redirect Message
A Packet Redirect message is used to transfer data packets between
the CE and FE. Usually, these data packets are control packets, but
they may be just data path packets that need further (exception or
high-touch) processing. It is also feasible that this message
carries no data packets and rather just meta data.
The Packet Redirect message data format is formatted as follows:
Message transfer direction:
CE to FE or FE to CE
Message header:
The Message Type in the header is set to MessageType=
'PacketRedirect'.
Doria, et al. Standards Track [Page 79]
RFC 5810 ForCES March 2010
Message body:
This consists of one or more TLVs that contain or describe the packet
being redirected. The TLV is specifically a Redirect TLV (with the
TLV Type="Redirect"). Detailed data format of a Redirect TLV for a
Packet Redirect message is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = Redirect | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Meta Data TLV |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Redirect Data TLV |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 39: Redirect_Data TLV
Meta Data TLV:
This is a TLV that specifies meta data associated with followed
redirected data. The TLV is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = METADATA-TLV | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Meta Data ILV |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
~ ... ~
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Meta Data ILV |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 40: METADATA-TLV
Doria, et al. Standards Track [Page 80]
RFC 5810 ForCES March 2010
Meta Data ILV:
This is an Identifier-Length-Value format that is used to describe
one meta data. The ILV has the format as:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Meta Data ID |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Meta Data Value |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 41: Meta Data ILV
where Meta Data ID is an identifier for the meta data, which is
statically assigned by the LFB definition.
Redirect Data TLV:
This is a TLV describing one packet of data to be directed via the
redirect operation. The TLV format is as follows:
0 1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type = REDIRECTDATA-TLV | Length |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Redirected Data |
. .
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Figure 42: Redirect Data TLV
Redirected Data:
This field contains the packet that is to be redirected in network
byte order. The packet should be 32 bits aligned as is the data for
all TLVs. The meta data infers what kind of packet is carried in
value field and therefore allows for easy decoding of data
encapsulated.
Doria, et al. Standards Track [Page 81]
RFC 5810 ForCES March 2010
To better illustrate the above PDU format, a tree structure for the
format is shown below:
main hdr (type = PacketRedirect)
|
|
+--- T = Redirect
. |
. +-- T = METADATA-TLV
| |
| +-- Meta Data ILV
| |
| +-- Meta Data ILV
| .
| .
|
+-- T = REDIRECTDATA-TLV
|
+-- // Redirected Data
Figure 43: PDU Format for Packet Redirect Message
7.10. Heartbeat Message
The Heartbeat (HB) message is used for one ForCES element (FE or CE)
to asynchronously notify one or more other ForCES elements in the
same ForCES NE on its liveness. Section 4.3.3 describes the traffic-
sensitive approach used.
A Heartbeat message is sent by a ForCES element periodically. The
parameterization and policy definition for heartbeats for an FE are
managed as components of the FE Protocol Object LFB, and can be set
by CE via a Config message. The Heartbeat message is a little
different from other protocol messages in that it is only composed of
a common header, with the message body left empty. A detailed
description of the message is as follows:
Message transfer direction:
FE to CE or CE to FE
Message header:
The Message Type in the message header is set to MessageType =
'Heartbeat'. Section 4.3.3 describes the HB mechanisms used. The
ACK flag in the header MUST be set to either 'NoACK' or 'AlwaysACK'
when the HB is sent.
Doria, et al. Standards Track [Page 82]
RFC 5810 ForCES March 2010
* When set to 'NoACK', the HB is not soliciting for a response.
* When set to 'AlwaysACK', the HB Message sender is always
expecting a response from its receiver. According to the HB
policies defined in Section 7.3.1, only the CE can send such
an HB message to query FE liveness. For simplicity and
because of the minimal nature of the HB message, the response
to an HB message is another HB message, i.e., no specific HB
Response message is defined. Whenever an FE receives an HB
message marked with 'AlwaysACK' from the CE, the FE MUST send
an HB message back immediately. The HB message sent by the
FE in response to the 'AlwaysACK' MUST modify the source and
destination IDs so that the ID of the FE is the source ID and
the CE ID of the sender is the destination ID, and MUST
change the ACK information to 'NoACK'. A CE MUST NOT respond
to an HB message with 'AlwaysACK' set.
* When set to anything else other than 'NoACK' or 'AlwaysACK',
the HB message is treated as if it was a 'NoACK'.
The correlator field in the HB message header SHOULD be set
accordingly when a response is expected so that a receiver can
correlate the response correctly. The correlator field MAY be
ignored if no response is expected.
Message body:
The message body is empty for the Heartbeat message.
8. High Availability Support
The ForCES protocol provides mechanisms for CE redundancy and
failover, in order to support High Availability as defined in
[RFC3654]. FE redundancy and FE to FE interaction is currently out
of scope of this document. There can be multiple redundant CEs and
FEs in a ForCES NE. However, at any one time only one primary CE can
control the FEs though there can be multiple secondary CEs. The FE
and the CE PL are aware of the primary and secondary CEs. This
information (primary, secondary CEs) is configured in the FE and in
the CE PLs during pre-association by the FEM and the CEM
respectively. Only the primary CE sends control messages to the FEs.
8.1. Relation with the FE Protocol
High Availability parameterization in an FE is driven by configuring
the FE Protocol Object LFB (refer to Appendix B and Section 7.3.1).
The FE Heartbeat Interval, CE Heartbeat Dead Interval, and CE
Doria, et al. Standards Track [Page 83]
RFC 5810 ForCES March 2010
Heartbeat policy help in detecting connectivity problems between an
FE and CE. The CE failover policy defines the reaction on a detected
failure.
Figure 44 extends the state machine illustrated in Figure 4 to allow
for new states that facilitate connection recovery.
(CE issues Teardown || +-----------------+
Lost association) && | Pre-association |
CE failover policy = 0 | (Association |
+------------>-->-->| in +<----+
| | progress) | |
| CE issues +--------+--------+ |
| Association | | CFTI
| Setup V | timer
| ___________________+ | expires
| | |
| V ^
+-+-----------+ +-------+-----+
| | | Not |
| | (CE issues Teardown || | Associated |
| | Lost association) && | |
| Associated | CE failover policy = 1 | (May |
| | | Continue |
| |---------->------->------>| Forwarding)|
| | | |
+-------------+ +-------------+
^ V
| |
| CE issues |
| Association |
| Setup |
+_________________________________________+
Figure 44: FE State Machine Considering HA
Section 4.2 describes transitions between the pre-association,
associated, and not associated states.
When communication fails between the FE and CE (which can be caused
by either the CE or link failure but not FE related), either the TML
on the FE will trigger the FE PL regarding this failure or it will be
detected using the HB messages between FEs and CEs. The
communication failure, regardless of how it is detected, MUST be
considered as a loss of association between the CE and corresponding
FE.
Doria, et al. Standards Track [Page 84]
RFC 5810 ForCES March 2010
If the FE's FEPO CE failover policy is configured to mode 0 (the
default), it will immediately transition to the pre-association
phase. This means that if association is again established, all FE
state will need to be re-established.
If the FE's FEPO CE failover policy is configured to mode 1, it
indicates that the FE is capable of HA restart recovery. In such a
case, the FE transitions to the not associated state and the CEFTI
timer is started. The FE MAY continue to forward packets during this
state. It MAY also recycle through any configured secondary CEs in a
round-robin fashion. It first adds its primary CE to the tail of
backup CEs and sets its primary CE to be the first secondary. It
then attempts to associate with the CE designated as the new primary
CE. If it fails to re-associate with any CE and the CEFTI expires,
the FE then transitions to the pre-association state.
If the FE, while in the not associated state, manages to reconnect to
a new primary CE before CEFTI expires, it transitions to the
associated state. Once re-associated, the FE tries to recover any
state that may have been lost during the not associated state. How
the FE achieves this is out of scope for this document.
Figure 45 below illustrates the ForCES message sequences that the FE
uses to recover the connection.
FE CE Primary CE Secondary
| | |
| Asso Estb,Caps exchg | |
1 |<--------------------->| |
| | |
| All msgs | |
2 |<--------------------->| |
| | |
| | |
| FAILURE |
| |
| Asso Estb,Caps exchange |
3 |<------------------------------------------>|
| |
| Event Report (pri CE down) |
4 |------------------------------------------->|
| |
| All Msgs |
5 |<------------------------------------------>|
Figure 45: CE Failover for Report Primary Mode
Doria, et al. Standards Track [Page 85]
RFC 5810 ForCES March 2010
A CE-to-CE synchronization protocol would be needed to support fast
failover as well as to address some of the corner cases; however,
this will not be defined by the ForCES protocol as it is out of scope
for this specification.
An explicit message (a Config message setting primary CE component in
the FE Protocol Object) from the primary CE can also be used to
change the primary CE for an FE during normal protocol operation.
Also note that the FEs in a ForCES NE could also use a multicast CE
ID, i.e., they could be associated with a group of CEs (this assumes
the use of a CE-CE synchronization protocol, which is out of scope
for this specification). In this case, the loss of association would
mean that communication with the entire multicast group of CEs has
been lost. The mechanisms described above will apply for this case
as well during the loss of association. If, however, the secondary
CE was also using the multicast CE ID that was lost, then the FE will
need to form a new association using a different CE ID. If the
capability exists, the FE MAY first attempt to form a new association
with the original primary CE using a different non-multicast CE ID.
8.2. Responsibilities for HA
TML level:
1. The TML controls logical connection availability and failover.
2. The TML also controls peer HA management.
At this level, control of all lower layers, for example, transport
level (such as IP addresses, MAC addresses, etc.) and associated
links going down are the role of the TML.
PL level:
All other functionality, including configuring the HA behavior during
setup, the CE IDs used to identify primary and secondary CEs,
protocol messages used to report CE failure (Event Report), Heartbeat
messages used to detect association failure, messages to change the
primary CE (Config), and other HA-related operations described
before, are the PL responsibility.
To put the two together, if a path to a primary CE is down, the TML
would take care of failing over to a backup path, if one is
available. If the CE is totally unreachable, then the PL would be
informed and it would take the appropriate actions described earlier.
Doria, et al. Standards Track [Page 86]
RFC 5810 ForCES March 2010
9. Security Considerations
The ForCES framework document [RFC3746], Section 8, goes into
extensive detail on a variety of security threats, the possible
effects of those threats on the protocol, and responses to those
threats. This document does not repeat that discussion; the reader
is referred to the ForCES framework document [RFC3746] for those
details and how the ForCES architecture addresses them.
ForCES PL uses security services provided by the ForCES TML. The TML
provides security services such as endpoint authentication service,
message authentication service, and confidentiality service.
Endpoint authentication service is invoked at the time of the pre-
association connection establishment phase and message authentication
is performed whenever the FE or CE receives a packet from its peer.
The following are the general security mechanisms that need to be in
place for ForCES PL.
o Security mechanisms are session controlled -- that is, once the
security is turned on depending upon the chosen security level (No
Security, Authentication, Confidentiality), it will be in effect
for the entire duration of the session.
o An operator should configure the same security policies for both
primary and backup FEs and CEs (if available). This will ensure
uniform operations and avoid unnecessary complexity in policy
configuration.
9.1. No Security
When "No Security" is chosen for ForCES protocol communication, both
endpoint authentication and message authentication service needs to
be performed by ForCES PL. Both these mechanism are weak and do not
involve cryptographic operation. An operator can choose "No
Security" level when the ForCES protocol endpoints are within a
single box, for example.
In order to have interoperable and uniform implementation across
various security levels, each CE and FE endpoint MUST implement this
level.
What is described below (in Section 9.1.1 and Section 9.1.2) are
error checks and not security procedures. The reader is referred to
Section 9.2 for security procedures.
Doria, et al. Standards Track [Page 87]
RFC 5810 ForCES March 2010
9.1.1. Endpoint Authentication
Each CE and FE PL maintains a list of associations as part of its
configuration. This is done via the CEM and FEM interfaces. An FE
MUST connect to only those CEs that are configured via the FEM;
similarly, a CE should accept the connection and establish
associations for the FEs which are configured via the CEM. The CE
should validate the FE identifier before accepting the connections
during the pre-association phase.
9.1.2. Message Authentication
When a CE or FE initiates a message, the receiving endpoint MUST
validate the initiator of the message by checking the common header
CE or FE identifiers. This will ensure proper protocol functioning.
This extra processing step is recommended even when the underlying
TML layer security services exist.
9.2. ForCES PL and TML Security Service
This section is applicable if an operator wishes to use the TML
security services. A ForCES TML MUST support one or more security
services such as endpoint authentication service, message
authentication service, and confidentiality service, as part of TML
security layer functions. It is the responsibility of the operator
to select an appropriate security service and configure security
policies accordingly. The details of such configuration are outside
the scope of the ForCES PL and are dependent on the type of transport
protocol and the nature of the connection.
All these configurations should be done prior to starting the CE and
FE.
When certificates-based authentication is being used at the TML, the
certificate can use a ForCES-specific naming structure as certificate
names and, accordingly, the security policies can be configured at
the CE and FE.
The reader is asked to refer to specific TML documents for details on
the security requirements specific to that TML.
9.2.1. Endpoint Authentication Service
When TML security services are enabled, the ForCES TML performs
endpoint authentication. Security association is established between
CE and FE and is transparent to the ForCES PL.
Doria, et al. Standards Track [Page 88]
RFC 5810 ForCES March 2010
9.2.2. Message Authentication Service
This is a TML-specific operation and is transparent to the ForCES PL.
For details, refer to Section 5.
9.2.3. Confidentiality Service
This is a TML-specific operation and is transparent to the ForCES PL.
For details, refer to Section 5.
10. Acknowledgments
The authors of this document would like to acknowledge and thank the
ForCES Working Group and especially the following: Furquan Ansari,
Alex Audu, Steven Blake, Shuchi Chawla, Alan DeKok, Ellen M.
Deleganes, Xiaoyi Guo, Yunfei Guo, Evangelos Haleplidis, Zsolt
Haraszti, Fenggen Jia, John C. Lin, Alistair Munro, Jeff Pickering,
T. Sridhlar, Guangming Wang, Chaoping Wu, and Lily L. Yang, for their
contributions. We would also like to thank David Putzolu and Patrick
Droz for their comments and suggestions on the protocol and for their
infinite patience. We would also like to thank Sue Hares and Alia
Atlas for extensive reviews of the document.
Alia Atlas did a wonderful job of shaping the document to make it
more readable by providing the IESG feedback.
Ross Callon was instrumental in getting us over major humps to
getting this document published.
The editors have used the xml2rfc [RFC2629] tools in creating this
document and are very grateful for the existence and quality of these
tools. The editor is also grateful to Elwyn Davies for his help in
correcting the XML source of this document.
11. References
11.1. Normative References
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2914] Floyd, S., "Congestion Control Principles", BCP 41,
RFC 2914, September 2000.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
Doria, et al. Standards Track [Page 89]
RFC 5810 ForCES March 2010
[RFC5390] Rosenberg, J., "Requirements for Management of Overload in
the Session Initiation Protocol", RFC 5390, December 2008.
[RFC5811] Hadi Salim, J. and K. Ogawa, "SCTP-Based Transport Mapping
Layer (TML) for the Forwarding and Control Element
Separation (ForCES) Protocol", RFC 5811, March 2010.
[RFC5812] Halpern, J. and J. Hadi Salim, "Forwarding and Control
Element Separation (ForCES) Forwarding Element Model",
RFC 5812, March 2010.
11.2. Informative References
[2PCREF] Gray, J., "Notes on database operating systems", in
"Operating Systems: An Advanced Course" Lecture Notes in
Computer Science, Vol. 60, pp. 394-481, Springer-Verlag,
1978.
[ACID] Haerder, T. and A. Reuter, "Principles of Transaction-
Orientated Database Recovery", 1983.
[RFC2629] Rose, M., "Writing I-Ds and RFCs using XML", RFC 2629,
June 1999.
[RFC3654] Khosravi, H. and T. Anderson, "Requirements for Separation
of IP Control and Forwarding", RFC 3654, November 2003.
[RFC3746] Yang, L., Dantu, R., Anderson, T., and R. Gopal,
"Forwarding and Control Element Separation (ForCES)
Framework", RFC 3746, April 2004.
Doria, et al. Standards Track [Page 90]
RFC 5810 ForCES March 2010
Appendix A. IANA Considerations
Following the policies outlined in "Guidelines for Writing an IANA
Considerations Section in RFCs" (RFC 5226 [RFC5226]), the following
namespaces are defined in ForCES.
o Message Type Namespace, Section 7
o Operation Type Namespace, Section 7.1.6
o Header Flags, Section 6.1
o TLV Type, Section 7
o TLV Result Values, Section 7.1.7
o LFB Class ID, Section 7.1.5 (resolved by model document,
[RFC5812].
o Result: Association Setup Response, Section 7.5.2
o Reason: Association Teardown Message, Section 7.5.3
A.1. Message Type Namespace
The Message Type is an 8-bit value. The following is the guideline
for defining the Message Type namespace:
Message Types 0x00 - 0x1F
Message Types in this range are part of the base ForCES protocol.
Message Types in this range are allocated through an IETF
consensus action [RFC5226].
Values assigned by this specification:
0x00 Reserved
0x01 AssociationSetup
0x02 AssociationTeardown
0x03 Config
0x04 Query
0x05 EventNotification
0x06 PacketRedirect
0x07 - 0x0E Reserved
0x0F Hearbeat
0x11 AssociationSetupResponse
0x12 Reserved
0x13 ConfigResponse
0x14 QueryResponse
Doria, et al. Standards Track [Page 91]
RFC 5810 ForCES March 2010
Message Types 0x20 - 0x7F
Message Types in this range are Specification Required [RFC5226].
Message Types using this range MUST be documented in an RFC or
other permanent and readily available reference.
Message Types 0x80 - 0xFF
Message Types in this range are reserved for vendor private
extensions and are the responsibility of individual vendors. IANA
management of this range of the Message Type namespace is
unnecessary.
A.2. Operation Selection
The Operation Selection (OPER-TLV) namespace is 16 bits long. The
following is the guideline for managing the OPER-TLV namespace.
OPER-TLV Type 0x0000-0x0FF
OPER-TLV Types in this range are allocated through an IETF
consensus process [RFC5226].
Values assigned by this specification:
0x0000 Reserved
0x0001 SET
0x0002 SET-PROP
0x0003 SET-RESPONSE
0x0004 SET-PROP-RESPONSE
0x0005 DEL
0x0006 DEL-RESPONSE
0x0007 GET
0x0008 GET-PROP
0x0009 GET-RESPONSE
0x000A GET-PROP-RESPONSE
0x000B REPORT
0x000C COMMIT
0x000D COMMIT-RESPONSE
0x000E TRCOMP
OPER-TLV Type 0x0100-0x7FFF
OPER-TLV Types using this range MUST be documented in an RFC or
other permanent and readily available reference [RFC5226].
OPER-TLV Type 0x8000-0xFFFF
OPER-TLV Types in this range are reserved for vendor private
extensions and are the responsibility of individual vendors. IANA
management of this range of the OPER-TLV Type namespace is
unnecessary.
Doria, et al. Standards Track [Page 92]
RFC 5810 ForCES March 2010
A.3. Header Flags
The Header flag field is 32 bits long. Header flags are part of
the ForCES base protocol. Header flags are allocated through an
IETF consensus action [RFC5226].
A.4. TLV Type Namespace
The TLV Type namespace is 16 bits long. The following is the
guideline for managing the TLV Type namespace.
TLV Type 0x0000-0x01FF
TLV Types in this range are allocated through an IETF consensus
process [RFC5226].
Values assigned by this specification:
0x0000 Reserved
0x0001 REDIRECT-TLV
0x0010 ASResult-TLV
0x0011 ASTreason-TLV
0x1000 LFBselect-TLV
0x0110 PATH-DATA-TLV
0x0111 KEYINFO-TLV
0x0112 FULLDATA-TLV
0x0113 SPARSEDATA-TLV
0x0114 RESULT-TLV
0x0115 METADATA-TLV
0x0116 REDIRECTDATA-TLV
TLV Type 0x0200-0x7FFF
TLV Types using this range MUST be documented in an RFC or other
permanent and readily available reference [RFC5226].
TLV Type 0x8000-0xFFFF
TLV Types in this range are reserved for vendor private extensions
and are the responsibility of individual vendors. IANA management
of this range of the TLV Type namespace is unnecessary.
Doria, et al. Standards Track [Page 93]
RFC 5810 ForCES March 2010
A.5. RESULT-TLV Result Values
The RESULT-TLV RTesult Value is an 8-bit value.
0x00 E_SUCCESS
0x01 E_INVALID_HEADER
0x02 E_LENGTH_MISMATCH
0x03 E_VERSION_MISMATCH
0x04 E_INVALID_DESTINATION_PID
0x05 E_LFB_UNKNOWN
0x06 E_LFB_NOT_FOUND
0x07 E_LFB_INSTANCE_ID_NOT_FOUND
0x08 E_INVALID_PATH
0x09 E_COMPONENT_DOES_NOT_EXIST
0x0A E_EXISTS
0x0B E_NOT_FOUND
0x0C E_READ_ONLY
0x0D E_INVALID_ARRAY_CREATION
0x0E E_VALUE_OUT_OF_RANGE
0x0F E_CONTENTS_TOO_LONG
0x10 E_INVALID_PARAMETERS
0x11 E_INVALID_MESSAGE_TYPE
0x12 E_E_INVALID_FLAGS
0x13 E_INVALID_TLV
0x14 E_EVENT_ERROR
0x15 E_NOT_SUPPORTED
0x16 E_MEMORY_ERROR
0x17 E_INTERNAL_ERROR
0x18-0xFE Reserved
0xFF E_UNSPECIFIED_ERROR
All values not assigned in this specification are designated as
Assignment by Expert Review.
A.6. Association Setup Response
The Association Setup Response namespace is 32 bits long. The
following is the guideline for managing the Association Setup
Response namespace.
Association Setup Response 0x0000-0x00FF
Association Setup Responses in this range are allocated through an
IETF consensus process [RFC5226].
Doria, et al. Standards Track [Page 94]
RFC 5810 ForCES March 2010
Values assigned by this specification:
0x0000 Success
0x0001 FE ID Invalid
0x0002 Permission Denied
Association Setup Response 0x0100-0x0FFF
Association Setup Responses in this range are Specification
Required [RFC5226]. Values using this range MUST be documented in
an RFC or other permanent and readily available reference
[RFC5226].
Association Setup Response 0x1000-0xFFFF
Association Setup Responses in this range are reserved for vendor
private extensions and are the responsibility of individual
vendors. IANA management of this range of the Association Setup
Response namespace is unnecessary.
A.7. Association Teardown Message
The Association Teardown Message namespace is 32 bits long. The
following is the guideline for managing the Association Teardown
Message namespace.
Association Teardown Message 0x00000000-0x0000FFFF
Association Teardown Messages in this range are allocated through
an IETF consensus process [RFC5226].
Values assigned by this specification:
0x00000000 Normal - teardown by administrator
0x00000001 Error - loss of heartbeats
0x00000002 Error - loss of bandwidth
0x00000003 Error - out of Memory
0x00000004 Error - application crash
0x000000FF Error - unspecified
Association Teardown Message 0x00010000-0x7FFFFFFF
Association Teardown Messages in this range are Specification
Required [RFC5226]. Association Teardown Messages using this
range MUST be documented in an RFC or other permanent and readily
available references. [RFC5226].
Association Teardown Message 0x80000000-0xFFFFFFFFF
Association Teardown Messages in this range are reserved for
vendor private extensions and are the responsibility of individual
Doria, et al. Standards Track [Page 95]
RFC 5810 ForCES March 2010
vendors. IANA management of this range of the Association
Teardown Message namespace is unnecessary.
Appendix B. ForCES Protocol LFB Schema
The schema described below conforms to the LFB schema described in
the ForCES model [RFC5812].
Section 7.3.1 describes the details of the different components
defined in this definition.
CEHBPolicyValues
The possible values of CE heartbeat policy
uchar
CEHBPolicy0
The CE heartbeat policy 0
CEHBPolicy1
The CE heartbeat policy 1
FEHBPolicyValues
The possible values of FE heartbeat policy
uchar
Doria, et al. Standards Track [Page 96]
RFC 5810 ForCES March 2010
FEHBPolicy0
The FE heartbeat policy 0
FEHBPolicy1
The FE heartbeat policy 1
FERestartPolicyValues
The possible values of FE restart policy
uchar
FERestartPolicy0
The FE restart policy 0
CEFailoverPolicyValues
The possible values of CE failover policy
uchar
CEFailoverPolicy0
The CE failover policy 0
Doria, et al. Standards Track [Page 97]
RFC 5810 ForCES March 2010
CEFailoverPolicy1
The CE failover policy 1
FEHACapab
The supported HA features
uchar
GracefullRestart
The FE supports Graceful Restart
HA
The FE supports HA
FEPO
The FE Protocol Object
1.0
CurrentRunningVersion
Currently running ForCES version
uchar
Doria, et al. Standards Track [Page 98]
RFC 5810 ForCES March 2010
FEID
Unicast FEID
uint32
MulticastFEIDs
the table of all multicast IDs
uint32
CEHBPolicy
The CE Heartbeat Policy
CEHBPolicyValues
CEHDI
The CE Heartbeat Dead Interval in millisecs
uint32
FEHBPolicy
The FE Heartbeat Policy
FEHBPolicyValues
FEHI
The FE Heartbeat Interval in millisecs
uint32
CEID
The Primary CE this FE is associated with
Doria, et al. Standards Track [Page 99]
RFC 5810 ForCES March 2010
uint32
BackupCEs
The table of all backup CEs other than the primary
uint32
CEFailoverPolicy
The CE Failover Policy
CEFailoverPolicyValues
CEFTI
The CE Failover Timeout Interval in millisecs
uint32
FERestartPolicy
The FE Restart Policy
FERestartPolicyValues
LastCEID
The Primary CE this FE was last associated with
uint32
SupportableVersions
the table of ForCES versions that FE supports
Doria, et al. Standards Track [Page 100]
RFC 5810 ForCES March 2010
uchar
HACapabilities
the table of HA capabilities the FE supports
FEHACapab
PrimaryCEDown
The pimary CE has changed
LastCEID
LastCEID
Doria, et al. Standards Track [Page 101]
RFC 5810 ForCES March 2010
B.1. Capabilities
Supportable Versions enumerates all ForCES versions that an FE
supports.
FEHACapab enumerates the HA capabilities of the FE. If the FE is not
capable of graceful restarts or HA, then it will not be able to
participate in HA as described in Section 8.1.
B.2. Components
All components are explained in Section 7.3.1.
Doria, et al. Standards Track [Page 102]
RFC 5810 ForCES March 2010
Appendix C. Data Encoding Examples
In this section a few examples of data encoding are discussed. These
example, however, do not show any padding.
==========
Example 1:
==========
Structure with three fixed-lengthof, mandatory fields.
struct S {
uint16 a
uint16 b
uint16 c
}
(a) Describing all fields using SPARSEDATA-TLV
PATH-DATA-TLV
Path to an instance of S ...
SPARSEDATA-TLV
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(b), lengthof(b), valueof(b)
ComponentIDof(c), lengthof(c), valueof(c)
(b) Describing a subset of fields
PATH-DATA-TLV
Path to an instance of S ...
SPARSEDATA-TLV
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(c), lengthof(c), valueof(c)
Note: Even though there are non-optional components in structure S,
since one can uniquely identify components, one can selectively send
components of structure S (e.g., in the case of an update from CE to
FE).
(c) Describing all fields using a FULLDATA-TLV
PATH-DATA-TLV
Path to an instance of S ...
FULLDATA-TLV
valueof(a)
valueof(b)
valueof(c)
Doria, et al. Standards Track [Page 103]
RFC 5810 ForCES March 2010
==========
Example 2:
==========
Structure with three fixed-lengthof fields, one mandatory, two
optional.
struct T {
uint16 a
uint16 b (optional)
uint16 c (optional)
}
This example is identical to example 1, as illustrated below.
(a) Describing all fields using SPARSEDATA-TLV
PATH-DATA-TLV
Path to an instance of S ...
SPARSEDATA-TLV
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(b), lengthof(b), valueof(b)
ComponentIDof(c), lengthof(c), valueof(c)
(b) Describing a subset of fields using SPARSEDATA-TLV
PATH-DATA-TLV
Path to an instance of S ...
SPARSEDATA-TLV
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(c), lengthof(c), valueof(c)
(c) Describing all fields using a FULLDATA-TLV
PATH-DATA-TLV
Path to an instance of S ...
FULLDATA-TLV
valueof(a)
valueof(b)
valueof(c)
Note: FULLDATA-TLV _cannot_ be used unless all fields are being
described.
Doria, et al. Standards Track [Page 104]
RFC 5810 ForCES March 2010
==========
Example 3:
==========
Structure with a mix of fixed-lengthof and variable-lengthof fields,
some mandatory, some optional. Note in this case, b is variable
sized.
struct U {
uint16 a
string b (optional)
uint16 c (optional)
}
(a) Describing all fields using SPARSEDATA-TLV
Path to an instance of U ...
SPARSEDATA-TLV
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(b), lengthof(b), valueof(b)
ComponentIDof(c), lengthof(c), valueof(c)
(b) Describing a subset of fields using SPARSEDATA-TLV
Path to an instance of U ...
SPARSEDATA-TLV
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(c), lengthof(c), valueof(c)
(c) Describing all fields using FULLDATA-TLV
Path to an instance of U ...
FULLDATA-TLV
valueof(a)
FULLDATA-TLV
valueof(b)
valueof(c)
Note: The variable-length field requires the addition of a FULLDATA-
TLV within the outer FULLDATA-TLV as in the case of component b
above.
Doria, et al. Standards Track [Page 105]
RFC 5810 ForCES March 2010
==========
Example 4:
==========
Structure containing an array of another structure type.
struct V {
uint32 x
uint32 y
struct U z[]
}
(a) Encoding using SPARSEDATA-TLV, with two instances of z[], also
described with SPARSEDATA-TLV, assuming only the 10th and 15th
subscripts of z[] are encoded.
path to instance of V ...
SPARSEDATA-TLV
ComponentIDof(x), lengthof(x), valueof(x)
ComponentIDof(y), lengthof(y), valueof(y)
ComponentIDof(z), lengthof(all below)
ComponentID = 10 (i.e index 10 from z[]), lengthof(all below)
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(b), lengthof(b), valueof(b)
ComponentID = 15 (index 15 from z[]), lengthof(all below)
ComponentIDof(a), lengthof(a), valueof(a)
ComponentIDof(c), lengthof(c), valueof(c)
Note the holes in the components of z (10 followed by 15). Also note
the gap in index 15 with only components a and c appearing but not b.
Doria, et al. Standards Track [Page 106]
RFC 5810 ForCES March 2010
Appendix D. Use Cases
Assume LFB with the following components for the following use cases.
foo1, type u32, ID = 1
foo2, type u32, ID = 2
table1: type array, ID = 3
components are:
t1, type u32, ID = 1
t2, type u32, ID = 2 // index into table2
KEY: nhkey, ID = 1, V = t2
table2: type array, ID = 4
components are:
j1, type u32, ID = 1
j2, type u32, ID = 2
KEY: akey, ID = 1, V = { j1,j2 }
table3: type array, ID = 5
components are:
someid, type u32, ID = 1
name, type string variable sized, ID = 2
table4: type array, ID = 6
components are:
j1, type u32, ID = 1
j2, type u32, ID = 2
j3, type u32, ID = 3
j4, type u32, ID = 4
KEY: mykey, ID = 1, V = { j1}
table5: type array, ID = 7
components are:
p1, type u32, ID = 1
p2, type array, ID = 2, array components of type-X
Type-X:
x1, ID 1, type u32
x2, ID2 , type u32
KEY: tkey, ID = 1, V = { x1}
All examples will use valueof(x) to indicate the value of the
referenced component x. In the case where F_SEL** are missing (bits
equal to 00) then the flags will not show any selection.
Doria, et al. Standards Track [Page 107]
RFC 5810 ForCES March 2010
All the examples only show use of FULLDATA-TLV for data encoding;
although SPARSEDATA-TLV would make more sense in certain occasions,
the emphasis is on showing the message layout. Refer to Appendix C
for examples that show usage of both FULLDATA-TLV and SPARSEDATA-TLV.
1. To get foo1
OPER = GET-TLV
PATH-DATA-TLV: IDCount = 1, IDs = 1
Result:
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV:
flags=0, IDCount = 1, IDs = 1
FULLDATA-TLV L = 4+4, V = valueof(foo1)
2. To set foo2 to 10
OPER = SET-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV: L = 4+4, V=10
Result:
OPER = SET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
3. To dump table2
OPER = GET-TLV
PATH-DATA-TLV:
IDCount = 1, IDs = 4
Result:
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 4
FULLDATA-TLV: L = XXX, V=
a series of: index, valueof(j1), valueof(j2)
representing the entire table
Note: One should be able to take a GET-RESPONSE-TLV and
convert it to a SET-TLV. If the result in the above example
is sent back in a SET-TLV (instead of a GET-RESPONSE_TLV),
then the entire contents of the table will be replaced at
that point.
Doria, et al. Standards Track [Page 108]
RFC 5810 ForCES March 2010
4. Multiple operations example. To create entry 0-5 of table2
(Error conditions are ignored)
OPER = SET-TLV
PATH-DATA-TLV:
flags = 0 , IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 0
FULLDATA-TLV valueof(j1), valueof(j2) of entry 0
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV valueof(j1), valueof(j2) of entry 1
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV valueof(j1), valueof(j2) of entry 2
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV valueof(j1), valueof(j2) of entry 3
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 4
FULLDATA-TLV valueof(j1), valueof(j2) of entry 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 5
FULLDATA-TLV valueof(j1), valueof(j2) of entry 5
Result:
OPER = SET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0 , IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 0
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 4
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 5
RESULT-TLV
Doria, et al. Standards Track [Page 109]
RFC 5810 ForCES March 2010
5. Block operations (with holes) example. Replace entry 0,2 of
table2.
OPER = SET-TLV
PATH-DATA-TLV:
flags = 0 , IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 0
FULLDATA-TLV containing valueof(j1), valueof(j2) of 0
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV containing valueof(j1), valueof(j2) of 2
Result:
OPER = SET-TLV
PATH-DATA-TLV:
flags = 0 , IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 0
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
6. Getting rows example. Get first entry of table2.
OPER = GET-TLV
PATH-DATA-TLV:
IDCount = 2, IDs = 4.0
Result:
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV:
IDCount = 2, IDs = 4.0
FULLDATA-TLV containing valueof(j1), valueof(j2)
Doria, et al. Standards Track [Page 110]
RFC 5810 ForCES March 2010
7. Get entry 0-5 of table2.
OPER = GET-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 0
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 5
Result:
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 4
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 0
FULLDATA-TLV containing valueof(j1), valueof(j2)
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV containing valueof(j1), valueof(j2)
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV containing valueof(j1), valueof(j2)
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV containing valueof(j1), valueof(j2)
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 4
FULLDATA-TLV containing valueof(j1), valueof(j2)
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 5
FULLDATA-TLV containing valueof(j1), valueof(j2)
Doria, et al. Standards Track [Page 111]
RFC 5810 ForCES March 2010
8. Create a row in table2, index 5.
OPER = SET-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 2, IDs = 4.5
FULLDATA-TLV containing valueof(j1), valueof(j2)
Result:
OPER = SET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 4.5
RESULT-TLV
9. Dump contents of table1.
OPER = GET-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 3
Result:
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV, Length = XXXX
(depending on size of table1)
index, valueof(t1),valueof(t2)
index, valueof(t1),valueof(t2)
.
.
.
Doria, et al. Standards Track [Page 112]
RFC 5810 ForCES March 2010
10. Using keys. Get row entry from table4 where j1=100. Recall, j1
is a defined key for this table and its KeyID is 1.
OPER = GET-TLV
PATH-DATA-TLV:
flags = F_SELKEY IDCount = 1, IDs = 6
KEYINFO-TLV = KeyID=1, KEY_DATA=100
Result:
If j1=100 was at index 10
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0, IDCount = 1, IDs = 6.10
FULLDATA-TLV containing
valueof(j1), valueof(j2),valueof(j3),valueof(j4)
11. Delete row with KEY match (j1=100, j2=200) in table2. Note that
the j1,j2 pair is a defined key for the table2.
OPER = DEL-TLV
PATH-DATA-TLV:
flags = F_SELKEY IDCount = 1, IDs = 4
KEYINFO-TLV: {KeyID =1 KEY_DATA=100,200}
Result:
If (j1=100, j2=200) was at entry 15:
OPER = DELETE-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0 IDCount = 2, IDs = 4.15
RESULT-TLV
Doria, et al. Standards Track [Page 113]
RFC 5810 ForCES March 2010
12. Dump contents of table3. It should be noted that this table has
a column with a component name that is variable sized. The
purpose of this use case is to show how such a component is to
be encoded.
OPER = GET-TLV
PATH-DATA-TLV:
flags = 0 IDCount = 1, IDs = 5
Result:
OPER = GET-RESPONSE-TLV
PATH-DATA-TLV:
flags = 0 IDCount = 1, IDs = 5
FULLDATA-TLV, Length = XXXX
index, someidv, TLV: T=FULLDATA-TLV, L = 4+strlen(namev),
V = valueof(v)
index, someidv, TLV: T=FULLDATA-TLV, L = 4+strlen(namev),
V = valueof(v)
index, someidv, TLV: T=FULLDATA-TLV, L = 4+strlen(namev),
V = valueof(v)
index, someidv, TLV: T=FULLDATA-TLV, L = 4+strlen(namev),
V = valueof(v)
.
.
.
Doria, et al. Standards Track [Page 114]
RFC 5810 ForCES March 2010
13. Multiple atomic operations.
Note 1: This emulates adding a new nexthop entry and then
atomically updating the L3 entries pointing to an old NH to
point to a new one. The assumption is that both tables are
in the same LFB.
Note: Observe the two operations on the LFB instance; both are
SET operations.
//Operation 1: Add a new entry to table2 index #20.
OPER = SET-TLV
Path-TLV:
flags = 0, IDCount = 2, IDs = 4.20
FULLDATA-TLV, V= valueof(j1),valueof(j2)
// Operation 2: Update table1 entry which
// was pointing with t2 = 10 to now point to 20
OPER = SET-TLV
PATH-DATA-TLV:
flags = F_SELKEY, IDCount = 1, IDs = 3
KEYINFO-TLV = KeyID=1 KEY_DATA=10
PATH-DATA-TLV
flags = 0 IDCount = 1, IDs = 2
FULLDATA-TLV, V= 20
Result:
//first operation, SET
OPER = SET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0 IDCount = 3, IDs = 4.20
RESULT-TLV code = success
FULLDATA-TLV, V = valueof(j1),valueof(j2)
// second operation SET - assuming entry 16 was updated
OPER = SET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0 IDCount = 2, IDs = 3.16
PATH-DATA-TLV
flags = 0 IDCount = 1, IDs = 2
RESULT-TLV code = success
FULLDATA-TLV, Length = XXXX v=20
Doria, et al. Standards Track [Page 115]
RFC 5810 ForCES March 2010
14. Selective setting. On table4 -- for indices 1, 3, 5, 7, and 9.
Replace j1 to 100, j2 to 200, j3 to 300. Leave j4 as is.
PER = SET-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 6
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV, Length = XXXX, V = {100}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV, Length = XXXX, V = {200}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV, Length = XXXX, V = {300}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV, Length = XXXX, V = {100}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV, Length = XXXX, V = {200}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV, Length = XXXX, V = {300}
Doria, et al. Standards Track [Page 116]
RFC 5810 ForCES March 2010
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 5
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV, Length = XXXX, V = {100}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV, Length = XXXX, V = {200}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV, Length = XXXX, V = {300}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 7
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV, Length = XXXX, V = {100}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV, Length = XXXX, V = {200}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV, Length = XXXX, V = {300}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 9
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
FULLDATA-TLV, Length = XXXX, V = {100}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
FULLDATA-TLV, Length = XXXX, V = {200}
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
FULLDATA-TLV, Length = XXXX, V = {300}
response:
OPER = SET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 6
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
Doria, et al. Standards Track [Page 117]
RFC 5810 ForCES March 2010
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 5
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 7
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 9
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 1
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 2
RESULT-TLV
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs = 3
RESULT-TLV
Doria, et al. Standards Track [Page 118]
RFC 5810 ForCES March 2010
15. Manipulation of table of table examples. Get x1 from table10
row with index 4, inside table5 entry 10.
operation = GET-TLV
PATH-DATA-TLV
flags = 0 IDCount = 5, IDs=7.10.2.4.1
Results:
operation = GET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0 IDCount = 5, IDs=7.10.2.4.1
FULLDATA-TLV: L=XXXX, V = valueof(x1)
16. From table5's row 10 table10, get X2s based on the value of x1
equaling 10 (recall x1 is KeyID 1).
operation = GET-TLV
PATH-DATA-TLV
flag = F_SELKEY, IDCount=3, IDS = 7.10.2
KEYINFO-TLV, KeyID = 1, KEYDATA = 10
PATH-DATA-TLV
IDCount = 1, IDS = 2 //select x2
Results:
If x1=10 was at entry 11:
operation = GET-RESPONSE-TLV
PATH-DATA-TLV
flag = 0, IDCount=5, IDS = 7.10.2.11
PATH-DATA-TLV
flags = 0 IDCount = 1, IDS = 2
FULLDATA-TLV: L=XXXX, V = valueof(x2)
17. Further example of manipulating a table of tables
Consider table6, which is defined as:
table6: type array, ID = 8
components are:
p1, type u32, ID = 1
p2, type array, ID = 2, array components of type type-A
type-A:
a1, type u32, ID 1,
a2, type array ID2 ,array components of type type-B
type-B:
b1, type u32, ID 1
b2, type u32, ID 2
Doria, et al. Standards Track [Page 119]
RFC 5810 ForCES March 2010
If for example one wanted to set by replacing:
table6.10.p1 to 111
table6.10.p2.20.a1 to 222
table6.10.p2.20.a2.30.b1 to 333
in one message and one operation.
There are two ways to do this:
a) using nesting
b) using a flat path data
A. Method using nesting
in one message with a single operation
operation = SET-TLV
PATH-DATA-TLV
flags = 0 IDCount = 2, IDs=6.10
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs=1
FULLDATA-TLV: L=XXXX,
V = {111}
PATH-DATA-TLV
flags = 0 IDCount = 2, IDs=2.20
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs=1
FULLDATA-TLV: L=XXXX,
V = {222}
PATH-DATA-TLV :
flags = 0, IDCount = 3, IDs=2.30.1
FULLDATA-TLV: L=XXXX,
V = {333}
Doria, et al. Standards Track [Page 120]
RFC 5810 ForCES March 2010
Result:
operation = SET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0 IDCount = 2, IDs=6.10
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs=1
RESULT-TLV
PATH-DATA-TLV
flags = 0 IDCount = 2, IDs=2.20
PATH-DATA-TLV
flags = 0, IDCount = 1, IDs=1
RESULT-TLV
PATH-DATA-TLV :
flags = 0, IDCount = 3, IDs=2.30.1
RESULT-TLV
B. Method using a flat path data in
one message with a single operation
operation = SET-TLV
PATH-DATA-TLV :
flags = 0, IDCount = 3, IDs=6.10.1
FULLDATA-TLV: L=XXXX,
V = {111}
PATH-DATA-TLV :
flags = 0, IDCount = 5, IDs=6.10.1.20.1
FULLDATA-TLV: L=XXXX,
V = {222}
PATH-DATA-TLV :
flags = 0, IDCount = 7, IDs=6.10.1.20.1.30.1
FULLDATA-TLV: L=XXXX,
V = {333}
Result:
operation = SET-TLV
PATH-DATA-TLV :
flags = 0, IDCount = 3, IDs=6.10.1
RESULT-TLV
PATH-DATA-TLV :
flags = 0, IDCount = 5, IDs=6.10.1.20.1
RESULT-TLV
PATH-DATA-TLV :
flags = 0, IDCount = 7, IDs=6.10.1.20.1.30.1
RESULT-TLV
Doria, et al. Standards Track [Page 121]
RFC 5810 ForCES March 2010
18. Get a whole LFB (all its components, etc.).
For example: At startup a CE might well want the entire FE
Object LFB. So, in a request targeted at class 1, instance
1, one might find:
operation = GET-TLV
PATH-DATA-TLV
flags = 0 IDCount = 0
result:
operation = GET-RESPONSE-TLV
PATH-DATA-TLV
flags = 0 IDCount = 0
FULLDATA-TLV encoding of the FE Object LFB
Doria, et al. Standards Track [Page 122]
RFC 5810 ForCES March 2010
Authors' Addresses
Avri Doria (editor)
Lulea University of Technology
Rainbow Way
Lulea SE-971 87
Sweden
Phone: +46 73 277 1788
EMail: avri@ltu.se
Jamal Hadi Salim (editor)
Znyx
Ottawa, Ontario
Canada
Phone:
EMail: hadi@mojatatu.com
Robert Haas (editor)
IBM
Saumerstrasse 4
8803 Ruschlikon
Switzerland
Phone:
EMail: rha@zurich.ibm.com
Hormuzd M Khosravi (editor)
Intel
2111 NE 25th Avenue
Hillsboro, OR 97124
USA
Phone: +1 503 264 0334
EMail: hormuzd.m.khosravi@intel.com
Doria, et al. Standards Track [Page 123]
RFC 5810 ForCES March 2010
Weiming Wang (editor)
Zhejiang Gongshang University
18, Xuezheng Str., Xiasha University Town
Hangzhou 310018
P.R. China
Phone: +86-571-28877721
EMail: wmwang@zjgsu.edu.cn
Ligang Dong
Zhejiang Gongshang University
18, Xuezheng Str., Xiasha University Town
Hangzhou 310018
P.R. China
Phone: +86-571-28877751
EMail: donglg@zjgsu.edu.cn
Ram Gopal
Nokia
5, Wayside Road
Burlington, MA 310035
USA
Phone: +1-781-993-3685
EMail: ram.gopal@nsn.com
Joel Halpern
P.O. Box 6049
Leesburg, VA 20178
USA
Phone: +1-703-371-3043
EMail: jmh@joelhalpern.com
Doria, et al. Standards Track [Page 124]
RFC, FYI, BCP