Internet Engineering Task Force (IETF) D. Thaler
Request for Comments: 6081 Microsoft
Updates: 4380 January 2011
Category: Standards Track
ISSN: 2070-1721
Teredo Extensions
Abstract
This document specifies a set of extensions to the Teredo protocol.
These extensions provide additional capabilities to Teredo, including
support for more types of Network Address Translations (NATs) and
support for more efficient communication.
Status of This Memo
This is an Internet Standards Track document.
This document is a product of the Internet Engineering Task Force
(IETF). It represents the consensus of the IETF community. It has
received public review and has been approved for publication by the
Internet Engineering Steering Group (IESG). Further information on
Internet Standards is available in Section 2 of RFC 5741.
Information about the current status of this document, any errata,
and how to provide feedback on it may be obtained at
http://www.rfc-editor.org/info/rfc6081.
Copyright Notice
Copyright (c) 2011 IETF Trust and the persons identified as the
document authors. All rights reserved.
This document is subject to BCP 78 and the IETF Trust's Legal
Provisions Relating to IETF Documents
(http://trustee.ietf.org/license-info) in effect on the date of
publication of this document. Please review these documents
carefully, as they describe your rights and restrictions with respect
to this document. Code Components extracted from this document must
include Simplified BSD License text as described in Section 4.e of
the Trust Legal Provisions and are provided without warranty as
described in the Simplified BSD License.
Thaler Standards Track [Page 1]
RFC 6081 Teredo Extensions January 2011
Table of Contents
1. Introduction . . . . . . . . . . . . . . . . . . . . . . . . . 3
2. Terminology . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
3.1. Symmetric NAT Support Extension . . . . . . . . . . . . . 9
3.2. UPnP-Enabled Symmetric NAT Extension . . . . . . . . . . . 11
3.3. Port-Preserving Symmetric NAT Extension . . . . . . . . . 13
3.4. Sequential Port-Symmetric NAT Extension . . . . . . . . . 14
3.5. Hairpinning Extension . . . . . . . . . . . . . . . . . . 15
3.6. Server Load Reduction Extension . . . . . . . . . . . . . 17
4. Message Syntax . . . . . . . . . . . . . . . . . . . . . . . . 18
4.1. Trailers . . . . . . . . . . . . . . . . . . . . . . . . . 18
4.2. Nonce Trailer . . . . . . . . . . . . . . . . . . . . . . 19
4.3. Alternate Address Trailer . . . . . . . . . . . . . . . . 19
4.4. Neighbor Discovery Option Trailer . . . . . . . . . . . . 20
4.5. Random Port Trailer . . . . . . . . . . . . . . . . . . . 21
5. Protocol Details . . . . . . . . . . . . . . . . . . . . . . . 22
5.1. Common Processing . . . . . . . . . . . . . . . . . . . . 22
5.1.1. Refresh Interval . . . . . . . . . . . . . . . . . . . 22
5.1.2. Trailer Processing . . . . . . . . . . . . . . . . . . 23
5.2. Symmetric NAT Support Extension . . . . . . . . . . . . . 23
5.2.1. Abstract Data Model . . . . . . . . . . . . . . . . . 24
5.2.2. Timers . . . . . . . . . . . . . . . . . . . . . . . . 24
5.2.3. Initialization . . . . . . . . . . . . . . . . . . . . 24
5.2.4. Message Processing . . . . . . . . . . . . . . . . . . 24
5.3. UPnP-Enabled Symmetric NAT Extension . . . . . . . . . . . 25
5.3.1. Abstract Data Model . . . . . . . . . . . . . . . . . 26
5.3.2. Timers . . . . . . . . . . . . . . . . . . . . . . . . 26
5.3.3. Initialization . . . . . . . . . . . . . . . . . . . . 27
5.3.4. Message Processing . . . . . . . . . . . . . . . . . . 28
5.3.5. Shutdown . . . . . . . . . . . . . . . . . . . . . . . 29
5.4. Port-Preserving Symmetric NAT Extension . . . . . . . . . 30
5.4.1. Abstract Data Model . . . . . . . . . . . . . . . . . 30
5.4.2. Timers . . . . . . . . . . . . . . . . . . . . . . . . 31
5.4.3. Initialization . . . . . . . . . . . . . . . . . . . . 32
5.4.4. Message Processing . . . . . . . . . . . . . . . . . . 32
5.5. Sequential Port-Symmetric NAT Extension . . . . . . . . . 35
5.5.1. Abstract Data Model . . . . . . . . . . . . . . . . . 35
5.5.2. Timers . . . . . . . . . . . . . . . . . . . . . . . . 36
5.5.3. Initialization . . . . . . . . . . . . . . . . . . . . 37
5.5.4. Message Processing . . . . . . . . . . . . . . . . . . 37
5.6. Hairpinning Extension . . . . . . . . . . . . . . . . . . 39
5.6.1. Abstract Data Model . . . . . . . . . . . . . . . . . 39
5.6.2. Timers . . . . . . . . . . . . . . . . . . . . . . . . 39
5.6.3. Initialization . . . . . . . . . . . . . . . . . . . . 39
5.6.4. Message Processing . . . . . . . . . . . . . . . . . . 40
Thaler Standards Track [Page 2]
RFC 6081 Teredo Extensions January 2011
5.7. Server Load Reduction Extension . . . . . . . . . . . . . 41
5.7.1. Abstract Data Model . . . . . . . . . . . . . . . . . 41
5.7.2. Timers . . . . . . . . . . . . . . . . . . . . . . . . 41
5.7.3. Initialization . . . . . . . . . . . . . . . . . . . . 42
5.7.4. Message Processing . . . . . . . . . . . . . . . . . . 42
6. Protocol Examples . . . . . . . . . . . . . . . . . . . . . . 42
6.1. Symmetric NAT Support Extension . . . . . . . . . . . . . 42
6.2. UPnP-Enabled Symmetric NAT Extension . . . . . . . . . . . 45
6.3. Port-Preserving Symmetric NAT Extension . . . . . . . . . 47
6.4. Sequential Port-Symmetric NAT Extension . . . . . . . . . 51
6.5. Hairpinning Extension . . . . . . . . . . . . . . . . . . 54
6.6. Server Load Reduction Extension . . . . . . . . . . . . . 57
7. Security Considerations . . . . . . . . . . . . . . . . . . . 58
8. Acknowledgements . . . . . . . . . . . . . . . . . . . . . . . 58
9. IANA Considerations . . . . . . . . . . . . . . . . . . . . . 58
10. References . . . . . . . . . . . . . . . . . . . . . . . . . . 58
10.1. Normative References . . . . . . . . . . . . . . . . . . . 58
10.2. Informative References . . . . . . . . . . . . . . . . . . 59
1. Introduction
This document specifies extensions to the Teredo protocol, as
specified in [RFC4380]. These extensions provide additional
capabilities to Teredo, including support for more types of Network
Address Translations (NATs) and support for more efficient
communication.
2. Terminology
Because this document extends [RFC4380], it uses the following
terminology, for consistency with [RFC4380].
Address-Restricted NAT: A restricted NAT that accepts packets from an
external host's IP address X and port Y if the internal host has sent
a packet that is destined to IP address X regardless of the
destination port. In the terminology of [RFC4787], this is a NAT
with Endpoint-Independent Mapping and Address-Dependent Filtering.
Address-Symmetric NAT: A symmetric NAT that has multiple external IP
addresses and that assigns different IP addresses and ports when
communicating with different external hosts.
Cone NAT: A NAT that maps all requests from the same internal IP
address and port to the same external IP address and port.
Furthermore, any external host can send a packet to the internal host
by sending a packet to the mapped external address and port. In the
terminology of [RFC4787], this is a NAT with Endpoint-Independent
Mapping and Endpoint-Independent Filtering.
Thaler Standards Track [Page 3]
RFC 6081 Teredo Extensions January 2011
Direct Bubble: A Teredo bubble that is sent directly to the IPv4 node
whose Teredo address is contained in the Destination field of the
IPv6 header, as specified in Section 2.8 of [RFC4380]. The IPv4
Destination Address and UDP Destination Port fields contain a mapped
address/port.
Echo Test: A mechanism to predict the mapped address/port a
sequential port-symmetric NAT is using for a client behind it.
Hairpinning: A feature that is available in some NATs where two or
more hosts are positioned behind a NAT and each of those hosts is
assigned a specific external (public) address and port by the NAT.
Hairpinning support in a NAT allows these hosts to send a packet to
the external address and port that is assigned to one of the other
hosts, and the NAT automatically routes the packet back to the
correct host. The term hairpinning is derived from the behavior of
the packet, which arrives on, and is sent out to, the same NAT
interface.
Indirect Bubble: A Teredo bubble that is sent indirectly (via the
destination's Teredo server) to another Teredo client, as specified
in Section 5.2.4 of [RFC4380].
Local Address/Port: The IPv4 address and UDP port from which a Teredo
client sends Teredo packets. The local port is referred to as the
Teredo service port in [RFC4380]. The local address of a node may or
may not be globally routable because the node can be located behind
one or more NATs.
Mapped Address/Port: A global IPv4 address and a UDP port that
results from the translation of a node's own local address/port by
one or more NATs. The node learns these values through the Teredo
protocol as specified in [RFC4380]. For symmetric NATs, the mapped
address/port can be different for every peer with which a node tries
to communicate.
Network Address Translation (NAT): The process of converting between
IP addresses used within an intranet or other private network and
Internet IP addresses.
Nonce: A time-variant random value used in the connection setup phase
to prevent message replay and other types of attacks.
Peer: A Teredo client with which another Teredo client needs to
communicate.
Thaler Standards Track [Page 4]
RFC 6081 Teredo Extensions January 2011
Port-Preserving NAT: A NAT that translates a local address/port to a
mapped address/port such that the mapped port has the same value as
the local port, as long as that same mapped address/port has not
already been used for a different local address/port.
Port-Restricted NAT: A restricted NAT that accepts packets from an
external host's IP address X and port Y only if the internal host has
sent a packet destined to IP address X and port Y. In the
terminology of [RFC4787], this is a NAT with Endpoint-Independent
Mapping and Address and Port-Dependent Filtering.
Port-Symmetric NAT: A symmetric NAT that has only a single external
IP address and hence only assigns different ports when communicating
with different external hosts.
Private Address: An IPv4 address that is not globally routable but is
part of the private address space specified in Section 3 of
[RFC1918].
Public Address: An external global address used by a NAT.
Restricted NAT: A NAT where all requests from the same internal IP
address and port are mapped to the same external IP address and port.
Unlike the cone NAT, an external host can send packets to an internal
host (by sending a packet to the external mapped address and port)
only if the internal host has first sent a packet to the external
host. There are two kinds of restricted NATs: address-restricted
NATs and port-restricted NATs.
Sequential Port-Symmetric NAT: A port-symmetric NAT that allocates
external ports sequentially for every {internal IP address and port,
destination IP address and port} tuple. The delta used in the
sequential assignment is typically 1 or 2 for most such NATs.
Symmetric NAT: A NAT where all requests from the same internal IP
address and port and to the same destination IP address and port are
mapped to the same external IP address and port. Requests from the
same internal IP address and port to a different destination IP
address and port may be mapped to a different external IP address and
port. Furthermore, a symmetric NAT accepts packets received from an
external host's IP address X and port Y only if some internal host
has sent packets to IP address X and port Y. In the terminology of
[RFC4787], this is a NAT with a mapping behavior of either Address-
Dependent Mapping or Address- and Port-Dependent Mapping, and a
filtering behavior of either Address-Dependent Filtering or Address-
and Port-Dependent Filtering.
Thaler Standards Track [Page 5]
RFC 6081 Teredo Extensions January 2011
Teredo Bubble: A Teredo control message (specified in Section 2.8 of
[RFC4380]) that is used to create a mapping in a NAT. There are two
types of Teredo bubbles: direct bubbles and indirect bubbles.
Teredo Client: A node that has access to the IPv4 Internet and wants
to gain access to the IPv6 Internet using the Teredo protocol.
Teredo IPv6 Address: An IPv6 address of a Teredo client, as specified
in Section 2.14 of [RFC4380].
Teredo Secondary Server Address: A secondary IPv4 address of a Teredo
server with which a Teredo client is configured, as specified in
Section 5.2 of [RFC4380].
Teredo Server: A node that has a globally routable address on the
IPv4 Internet, and is used as a helper to provide IPv6 connectivity
to Teredo clients.
Teredo Server Address: A (primary) IPv4 address of a Teredo server
with which a Teredo client is configured, as specified in Section 5.2
of [RFC4380].
UPnP-enabled NAT: A NAT that has the UPnP device control protocol
enabled, as specified in [UPNPWANIP]. (Note that today, by default,
most UPnP-capable NATs have the UPnP device control protocol
disabled.)
The key words "MUST", "MUST NOT", "REQUIRED", "SHALL", "SHALL NOT",
"SHOULD", "SHOULD NOT", "RECOMMENDED", "MAY", and "OPTIONAL" in this
document are to be interpreted as described in RFC 2119 [RFC2119].
3. Overview
The Teredo protocol (as specified in [RFC4380]) enables nodes located
behind one or more IPv4 NATs to obtain IPv6 connectivity by tunneling
packets over UDP.
When a node behind a NAT needs to communicate with a peer (i.e.,
another node) that is behind a NAT, there are four sets of IPv4
address/port pairs of interest:
o The node's own IPv4 address/port.
o The external IPv4 address/port to which the node's NAT translates.
o The peer's own IPv4 address/port.
o The external IPv4 address/port to which the peer's NAT translates.
Thaler Standards Track [Page 6]
RFC 6081 Teredo Extensions January 2011
When the node sends a packet to a peer, the node needs to send it
from the node's own IPv4 address/port, destined to the peer's
external IPv4 address/port. By the time it arrives at the peer
(i.e., after passing through both NATs), the peer will see the same
packet as coming from the node's external IPv4 address/port, destined
to the peer's own IPv4 address/port.
In this document, the term local address/port refers to a Teredo
client's own IPv4 address/port, and mapped address/port refers to the
external IPv4 address/port to which its NAT translates the local
address/port. That is, the mapped address/port is what the IPv4
Internet sees the Teredo client as.
A Teredo client running on a node communicates with a Teredo server
to discover its mapped address/port. The mapped address/port, along
with the Teredo server address, is used to generate an IPv6 address
known as a Teredo IPv6 address. This allows any peer that gets the
node's IPv6 address to easily determine the external IPv4 address/
port to which to send IPv6 packets encapsulated in IPv4 UDP messages.
This document specifies extensions to the Teredo protocol. These
Teredo extensions are independent of each other and can be
implemented in isolation, except that the UPnP-Symmetric NAT
Extension and the Port-Preserving Symmetric NAT Extension both
require the Symmetric NAT Support Extension to be implemented. An
implementation of this specification can support any combination of
the Teredo extensions, subject to the above-mentioned restriction.
The following matrix outlines the connectivity improvements of some
of the extensions outlined in this document.
Thaler Standards Track [Page 7]
RFC 6081 Teredo Extensions January 2011
Destination NAT
| | | | | | Port-| | |
| | | | UPnP | UPnP | pres.| Seq. | |
| | Addr.| Port | Port | Port | Port-| Port-| Port-| Addr
Source NAT| Cone | rest.| rest.| rest.| symm.| symm.| symm.| symm.| symm
----------+------+------+------+------+------+------+------+------+-----
Cone | Yes | Yes | Yes | Yes | SNS | SNS | SNS | SNS | SNS
----------+------+------+------+------+------+------+------+------+-----
Address | Yes | Yes | Yes | Yes | SNS | SNS | SNS | SNS | No
restricted| | | | | | | | |
----------+------+------+------+------+------+------+------+------+-----
Port | Yes | Yes | Yes | Yes | No | SNS+ | SNS+ | No | No
restricted| | | | | | PP | SS | |
----------+------+------+------+------+------+------+------+------+-----
UPnP Port-| Yes | Yes | Yes | Yes | SNS+ | No | No | No | No
restricted| | | | | UPnP | | | |
----------+------+------+------+------+------+------+------+------+-----
UPnP Port | SNS | SNS | No | SNS+ | SNS+ | No | No | No | No
symmetric | | | | UPnP | UPnP | | | |
----------+------+------+------+------+------+------+------+------+-----
Port- | | | SNS | | | SNS | SNS | |
preserving| SNS | SNS | + | No | No | + | + | No | No
Port- | | | PP | | | PP | SS | |
symmetric | | | | | | | | |
----------+------+------+------+------+------+------+------+------+-----
Sequential| | | SNS | | | | | |
Port- | SNS | SNS | + | No | No | No | No | No | No
symmetric | | | SS | | | | | |
----------+------+------+------+------+------+------+------+------+-----
Port- | SNS | SNS | No | No | No | No | No | No | No
symmetric | | | | | | | | |
----------+------+------+------+------+------+------+------+------+-----
Address- | SNS | No | No | No | No | No | No | No | No
symmetric | | | | | | | | |
----------+------+------+------+------+------+------+------+------+-----
Yes = Supported by [RFC4380].
SNS = Supported with the Symmetric NAT Support Extension.
SNS+UPnP = Supported with the Symmetric NAT Support Extension and UPnP
Symmetric NAT Extension.
SNS+PP = Supported with the Symmetric NAT Support Extension and Port-
Preserving Symmetric NAT Extension.
SNS+SS = Supported with the Symmetric NAT Support Extension and
Sequential Port-Symmetric NAT Extension.
Thaler Standards Track [Page 8]
RFC 6081 Teredo Extensions January 2011
No = No connectivity.
Figure 1: Matrix of Connectivity Improvements for Teredo Extensions
Note that as with [RFC4380], if the qualification process is not
successful, Teredo will not be configured with an IPv6 address, and
connectivity will function as if Teredo were not present. Similarly,
for any combination of NAT types that are not supported by Teredo and
the extensions defined herein, the connectivity tests between a
client and a peer will fail within a finite period of time, allowing
the client to handle this case as with any other type of unreachable
destination address (e.g., by trying another address of the
destination such as a native IPv4 address).
3.1. Symmetric NAT Support Extension
The qualification procedure (as specified in Section 5.2.1 of
[RFC4380]) is a process that allows a Teredo client to determine the
type of NAT that it is behind, in addition to its mapped address/port
as seen by its Teredo server. However, Section 5.2.1 of [RFC4380]
suggests that if the client learns it is behind a symmetric NAT, the
Teredo client should go into an "offline state" where it is not able
to use Teredo. The primary reason for doing so is that it is not
easy for Teredo clients to connect to each other if either or both of
them are positioned behind a symmetric NAT. Because of the way a
symmetric NAT works, a peer sees a different mapped address/port in
the IPv4/UDP headers of packets coming from a Teredo client than the
node's Teredo server sees (and hence appears in the node's Teredo
IPv6 address). Consequently, a symmetric NAT does not allow incoming
packets from a peer that are addressed to the mapped address/port
embedded in the node's Teredo IPv6 address. Thus, the incoming
packets are dropped and communication with Teredo clients behind
symmetric NATs is not established.
With the Symmetric NAT Support Extension, Teredo clients begin to use
Teredo even after they detect that they are positioned behind a
symmetric NAT.
Consider the topology shown in Figure 2. Teredo Client B uses Teredo
Server 2 to learn that its mapped address/port is 192.0.2.10:8192,
and constructs a Teredo IPv6 address, as specified in Section 4 of
[RFC4380]. Hence, c633:6476 is the hexadecimal value of the address
of Teredo Server 2 (198.51.100.118), the mapped port is exclusive-
OR'ed with 0xffff to form dfff, and the Mapped Address is exclusive-
OR'ed with 0xffffffff to form 3fff:fdf5.
Thaler Standards Track [Page 9]
RFC 6081 Teredo Extensions January 2011
Teredo Client A uses Teredo Server 1 to learn that its mapped
address/port is 192.0.2.1:4096 and, with this extension, constructs a
Teredo IPv6 address (as specified in Section 4 of [RFC4380]) even
though it learns that it is behind a symmetric NAT. Hence, cb00:7178
is the hexadecimal value of the address of Teredo Server 1
(203.0.113.120), the mapped port is exclusive-OR'ed with 0xffff to
form efff, and the Mapped Address is exclusive-OR'ed with 0xffffffff
to form 3fff:fdfe.
The Symmetric NAT Support Extension enables a Teredo client
positioned behind a symmetric NAT to communicate with Teredo peers
positioned behind a cone or address-restricted NATs as follows,
depending on what side initiates the communication.
--------------------------------------------
/ \
< IPv6 Internet >
\ /
-|----------------------------------------|-
| |
+----------+ +----------+
| Teredo | | Teredo |
| Server 1 | | Server 2 |
+----------+ +----------+
203.0.113.120| 198.51.100.118|
-|----------------------------------------|-
/ \
< IPv4 Internet >
\ /
-|----------------------------------------|-
192.0.2.1| 192.0.2.10|
UDP port 4096| UDP port 8192|
+---------+ +----------+
|Symmetric| |Other type|
| NAT | | of NAT |
+---------+ +----------+
| |
+-----------------+ +-----------------+
| Teredo client A | | Teredo client B |
+-----------------+ +-----------------+
2001:0:cb00:7178:0:efff:3fff:fdfe 2001:0:c633:6476:0:dfff:3fff:fdf5
Teredo Address Teredo Address
Figure 2: Symmetric NAT Example
In the first case, assume that a Teredo Client B (B) positioned
behind a cone or address-restricted NATs initiates communication with
Teredo Client A (A) positioned behind a symmetric NAT. B sends an
Thaler Standards Track [Page 10]
RFC 6081 Teredo Extensions January 2011
indirect bubble via A's server (Teredo Server 1) to A, and A responds
with a direct bubble. This direct bubble reaches B, because it is
positioned behind a cone or address-restricted NAT. However, the
mapped address/port in the IPv4/UDP headers of the direct bubble are
different from the mapped address/port embedded in A's Teredo IPv6
address. B therefore remembers the mapped address/port of the direct
bubble and uses them for future communication with A, and thus
communication is established.
In the second case, assume that A, positioned behind a symmetric NAT,
initiates communication with B, positioned behind a cone or address-
restricted NAT. A sends an indirect bubble to B via B's server
(Teredo Server 2), and B responds with a direct bubble. This direct
bubble is dropped by A's symmetric NAT because the direct bubble is
addressed to the mapped address/port embedded in A's Teredo IPv6
address. However, communication can be established by having B
respond with an indirect bubble via A's server (Teredo Server 1).
Now the scenario is similar to the first case and communication will
be established.
3.2. UPnP-Enabled Symmetric NAT Extension
The UPnP-enabled Symmetric NAT Extension is dependent on the
Symmetric NAT Support Extension. Only if Teredo clients have been
enabled to acquire a Teredo IPv6 address in spite of being behind a
symmetric NAT will this extension help in traversing UPnP-enabled
Symmetric NATs.
The Symmetric NAT Support Extension enables communication between
Teredo clients behind symmetric NATs with Teredo clients behind cone
NATs or address-restricted NATs. However, clients behind symmetric
NATs can still not communicate with clients behind port-restricted
NATs or symmetric NATs.
Referring again to Figure 2 (see Section 3.1), assume that Teredo
Client A is positioned behind a symmetric NAT and initiates
communication with Client B, which is positioned behind a port-
restricted NAT. Client A sends a direct bubble and an indirect
bubble to Client B via Client B's server (Teredo Server 2). As per
the characteristics of the symmetric NAT, the IPv4 source of the
direct bubble contains a different mapped address and/or port than
the one embedded in the Teredo server. This direct bubble is dropped
because Client B's NAT does not have state to let it pass through,
and Client B does not learn the mapped address/port used in the IPv4/
UDP headers. In response to the indirect bubble from Client A,
Client B sends a direct bubble destined to the mapped address/port
embedded in Client A's Teredo IPv6 address. This direct bubble is
dropped because Client A's NAT does not have state to accept packets
Thaler Standards Track [Page 11]
RFC 6081 Teredo Extensions January 2011
destined to that mapped address/port. The direct bubble does,
however, cause Client B's NAT to set up outgoing state for the mapped
address/port embedded in Client A's Teredo IPv6 address.
As described in Section 3.1, Client B also sends an indirect bubble
that elicits a direct bubble from Client A. Unlike the case in
Section 3.1, however, the direct bubble from Client A is dropped as
Client B's NAT does not have state for the mapped address/port that
Client A's NAT uses. Note that Client B's NAT is port-restricted and
hence requires both the mapped address and port to be the same as in
its outgoing state, whereas in Section 3.1, Client A's NAT was a cone
or address-restricted NAT which only required the mapped address (but
not port) to be the same. Thus, communication between Client A and
Client B fails. If Client B were behind a symmetric NAT, the problem
is further complicated by Client B's NAT using a different outgoing
mapped address/port than the one embedded in Client B's Teredo IPv6
address.
If a Teredo client is separated from the global Internet by a single
UPnP-enabled symmetric or port-restricted NAT, it can communicate
with other Teredo clients that are positioned behind a single UPnP-
enabled symmetric or port-restricted NAT as follows.
Teredo clients, before communicating with the Teredo server during
the qualification procedure, use UPnP to reserve a translation from a
local address/port to a mapped-address/port. Therefore, during the
qualification procedure, the Teredo server reflects back the reserved
mapped address/port, which then is included in the Teredo IPv6
address. The mapping created by UPnP allows the NAT to forward
packets destined for the mapped address/port to the local address/
port, independent of the source of the packets. It typically does
not, however, cause packets sourced from the local address/port to be
translated to have the mapped address/port as the external source and
hence continues to function as a symmetric NAT in this respect.
Thus, a Teredo client, positioned behind a UPnP-enabled symmetric
NAT, can receive a direct bubble sent by any Teredo peer. The Teredo
client compares the peer's mapped address/port as seen in the IPv4/
UDP headers with the mapped address/port in the peer's Teredo IPv6
address. If the two mappings are different, the packet was sent by
another Teredo client positioned behind a symmetric NAT. The
Symmetric NAT Support Extension suggested that the Teredo client use
the peer's mapped address/port seen in the IPv4/UDP headers for
future communication. However, because symmetric NAT-to-symmetric
NAT communication would not have been possible anyway, the Teredo
client sends back a direct bubble to the mapped port/address embedded
Thaler Standards Track [Page 12]
RFC 6081 Teredo Extensions January 2011
in the peer's Teredo IPv6 address. If the peer is also situated
behind a UPnP-enabled NAT, the direct bubble will make it through and
communication will be established.
Even though communication is established between the two Teredo IPv6
addresses, the mappings will be asymmetric in the two directions of
data transfer. Specifically, incoming packets will be destined to
the reserved mapped address/port that is embedded in the Teredo IPv6
address. Outgoing packets will instead appear to come from a
different mapped address/port due to the symmetric NAT behavior.
3.3. Port-Preserving Symmetric NAT Extension
The Port-Preserving Symmetric NAT Extension is dependent on the
Symmetric NAT Support Extension (Section 3.1). Only if Teredo
clients have been enabled to acquire a Teredo IPv6 address in spite
of being behind a symmetric NAT will this extension help in
traversing port-preserving symmetric NATs.
The Symmetric NAT Support Extension enables communication between
Teredo clients behind symmetric NATs with Teredo clients behind cone
NATs or address-restricted NATs. However, clients behind symmetric
NATs can still not communicate with clients behind port-restricted or
symmetric NATs, as described in Section 3.2. Note that the Port-
Preserving Symmetric NAT Extension described here is independent of
the UPnP-enabled Symmetric NAT Extension, described in Section 3.2.
If a Teredo client is positioned behind a port-preserving symmetric
NAT, the client can communicate with other Teredo clients positioned
behind a port-restricted NAT or a port-preserving symmetric NAT as
follows.
Teredo clients compare the mapped port learned during the
qualification procedure with their local port to determine if they
are positioned behind a port-preserving NAT. If both the mapped port
and the local port have the same value, the Teredo client is
positioned behind a port-preserving NAT. At the end of the
qualification procedure, the Teredo client also knows if it is
positioned behind a symmetric NAT, as described in Section 3.1.
Teredo clients positioned behind port-preserving symmetric NATs can
also listen on randomly chosen local ports. If the randomly chosen
local port has not been used by the symmetric NAT as a mapped port in
a prior port-mapping, the NAT uses the same port number as the mapped
port. Thus, the challenge is to get the first direct bubble sent out
from the random port to be destined to a valid destination address
and port. When the mapped address/port is embedded in the
destination's Teredo IPv6 address, this is easy.
Thaler Standards Track [Page 13]
RFC 6081 Teredo Extensions January 2011
The communication setup is more complicated when the destination
Teredo client is also positioned behind a port-preserving symmetric
NAT. In such a case, both Teredo clients need to send their first
direct bubbles to the correct destination mapped address/port. Thus,
the protocol messages, which communicate one Teredo client's random
port number to the other Teredo client, must be exchanged indirectly
(via Teredo servers). When one Teredo client has access to the other
Teredo client's random port number, it can send a direct bubble
destined to the mapped address embedded in the destination's Teredo
IPv6 address, and the mapped port can be the same as the
destination's random port number. If both NATs are port-preserving,
port-preserved mappings are created on both NATs and the second
direct bubble succeeds in reaching the destination.
3.4. Sequential Port-Symmetric NAT Extension
The Sequential Port-Symmetric NAT Extension is dependent on the
Symmetric NAT Support Extension (Section 3.1). This extension helps
in traversing a sequential port-symmetric NAT only if Teredo clients
are enabled to acquire a Teredo IPv6 address even when behind a
symmetric NAT.
When the Sequential Port-Symmetric NAT Extension is used, if a Teredo
client is positioned behind a sequential port-symmetric NAT, the
client can communicate with other Teredo clients that are positioned
behind a port-restricted NAT as follows.
During qualification, if the client discovers it is behind a
symmetric NAT that is not port-preserving, the client assumes by
default that it is behind a sequential port-symmetric NAT. This
assumption is proactive for the following reasons:
o There is no perfect method of discovering whether the client is
behind a sequential port-symmetric NAT.
o These kinds of NATs are notorious for changing their behavior. At
times, they could be sequential port-symmetric and at other times
not.
o There is no other solution for symmetric NAT traversal so this is
a last resort.
Teredo clients positioned behind sequential port-symmetric NATs can
also listen on a randomly chosen local port when communicating with a
peer. To predict the external port being used for a given peer, the
client sends three packets:
Thaler Standards Track [Page 14]
RFC 6081 Teredo Extensions January 2011
o Packet 1 is a router solicitation (as specified in Section 5.2.1
of [RFC4380]) sent to the Teredo server address.
o Packet 2 is a direct bubble sent to the peer.
o Packet 3 is a router solicitation sent to the secondary Teredo
server address.
As part of the normal Teredo protocol, the Teredo server responds to
packets 1 and 3. Based on the information in the responses, the
client now knows that Packet 1 was seen as coming from one external
port, and Packet 3 was seen as coming from another external port.
Assuming the NAT is a sequential port-symmetric NAT, the external
port for Packet 2 is estimated (or predicted) to be midway between
the external ports for Packets 1 and 3. Note that because other
applications might also have been using the NAT between packets 1 and
3, the actual port might not be exactly the midpoint.
The Teredo client then communicates the predicted port to its peer,
which sends a direct bubble to the communicated port. If the
communicated port is indeed the external port for Packet 2, the
direct bubble will reach the Teredo client.
3.5. Hairpinning Extension
Hairpinning support in a NAT routes packets that are sent from a
private (local) address destined to a public (mapped) address of the
NAT, back to another private (local) destination address behind the
same NAT. If hairpinning support is not available in a NAT, two
Teredo clients behind the same NAT are not able to communicate with
each other, as specified in Section 8.3 of [RFC4380].
The Hairpinning Extension enables two clients behind the same NAT to
talk to each other when the NAT does not support hairpinning. This
process is illustrated in the following diagram.
Thaler Standards Track [Page 15]
RFC 6081 Teredo Extensions January 2011
--------------------------------------------
/ \
< IPv6 Internet >
\ /
--------------------|-----------------------
|
+----------+
| Teredo |
| Server |
+----------+
203.0.113.120|
--------------------|-----------------------
/ \
< IPv4 Internet >
\ /
--------------------|-----------------------
198.51.100.118|
NAT +-------+
without | NAT |
hairpinning | E |
support +-------+
|
+------------------+--------------------+
192.168.1.0| 192.168.1.1|
UDP port 4095| UDP port 4096|
+---------+ +----------+
| NAT | | NAT |
| F | | G |
+---------+ +----------+
| |
+-----------------+ +-----------------+
| Teredo client A | | Teredo client B |
+-----------------+ +-----------------+
2001:0:cb00:7178:0:f000:39cc:9b89 2001:0:cb00:7178:0:efff:39cc:9b89
Teredo Address Teredo Address
Figure 3: Hairpinning Example
The Teredo Client A (A) includes, as part of its indirect bubble sent
to Teredo Client B (B), its local address/port. B, upon receiving
the indirect bubble, tries to establish communication by sending
direct bubbles to the mapped address/port of A, and also to the local
address/port of B.
If a Teredo client is part of a multi-NAT hierarchy and the NAT to
which the Teredo client is connected supports the UPnP protocol (as
specified in [UPNPWANIP]), the Teredo client can use UPnP to
determine the mapped address/port assigned to it by the NAT. This
Thaler Standards Track [Page 16]
RFC 6081 Teredo Extensions January 2011
information can be included along with the local address/port when
sending the indirect bubble. The destination Teredo client now tries
to establish a connection by sending direct bubbles to the mapped
address/port in the Teredo IPv6 address, to the local address/port
included in the bubble, and also to the mapped address/port included
in the bubble.
Note that UPnP support is only required if the Teredo clients are
behind different NATs in a multi-NAT hierarchy. Without UPnP
support, the Hairpinning Extension still allows two hosts behind the
same non-hairpinning NAT to communicate using their Teredo IPv6
addresses.
3.6. Server Load Reduction Extension
If communication between a Teredo client and a Teredo peer was
successfully established but at a later stage was silent for a while,
for efficiency, it is best to refresh the mapping state in the NATs
that are positioned between them. To refresh the communication
between itself and a Teredo peer, a Teredo client needs to solicit a
direct bubble response from the Teredo peer. An indirect bubble is
sent to solicit a direct bubble response from a Teredo peer, as
specified in Section 5.2.4 of [RFC4380]. However, these indirect
bubbles increase the load on the Teredo server.
The Server Load Reduction Extension allows Teredo clients to send
direct bubbles most of the time instead of sending indirect bubbles
all of the time in the following way:
1. When a Teredo client tries to refresh its communication with a
Teredo peer, it uses a direct bubble instead of an indirect
bubble. However, because direct bubbles do not normally solicit
a response, the direct bubble format is extended to be able to
solicit a response.
2. When a Teredo client receives a direct bubble that is soliciting
a response, the Teredo client responds with a direct bubble.
3. If attempts to re-establish communication with the help of direct
bubbles fail, the Teredo client starts over the process of
establishing communication with the Teredo peer, as specified in
Section 5.2.4 of [RFC4380].
Thaler Standards Track [Page 17]
RFC 6081 Teredo Extensions January 2011
4. Message Syntax
All Teredo messages are transported over the User Datagram Protocol
(UDP), as specified in Section 3 of [RFC4380].
In addition, Section 5.2.3 of [RFC4380] states:
An IPv6 packet is deemed valid if it conforms to [RFC2460]: the
protocol identifier should indicate an IPv6 packet and the payload
length should be consistent with the length of the UDP datagram in
which the packet is encapsulated. In addition, the client should
check that the IPv6 destination address correspond [sic] to its
own Teredo address.
This document updates the word "consistent" above as follows. The
IPv6 payload length is "consistent" with the length of the UDP
datagram if the IPv6 packet length (i.e., the Payload Length value in
the IPv6 header plus the IPv6 header size) is less than or equal to
the UDP payload length (i.e., the Length value in the UDP header
minus the UDP header size). This allows the use of trailers after
the IPv6 packet, which are defined in the following sections.
4.1. Trailers
Teredo packets can carry a variable number of type-length-value (TLV)
encoded trailers, of the following format (intended to be similar to
the use of IPv6 options defined in [RFC2460] section 4.2):
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Value (variable) |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type (1 byte): 8-bit identifier of the type of trailer.
Length (1 byte): 8-bit unsigned integer. Length of the Value field
of this trailer, in octets.
Value (variable): Trailer-Type-specific data.
The trailer Type identifiers are internally encoded such that their
highest-order two bits specify the action that is to be taken if the
host does not recognize the trailer Type:
Thaler Standards Track [Page 18]
RFC 6081 Teredo Extensions January 2011
00, 10, 11 - skip over this trailer and continue processing the
packet.
01 - discard the packet.
4.2. Nonce Trailer
The Nonce Trailer is used by the Symmetric NAT Support Extension (and
therefore the UPnP-enabled Symmetric NAT Extension and Port-
Preserving Symmetric NAT Extension also) and the Hairpinning
Extension. The Nonce Trailer can be present in both indirect and
direct bubbles. The nonce in the Nonce Trailer helps authenticate a
Teredo client positioned behind a Symmetric NAT.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Nonce |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type (1 byte): The Trailer Option type. This field MUST be set to
0x01.
Length (1 byte): The length in bytes of the rest of the option. This
field MUST be set to 0x04.
Nonce (4 bytes): The nonce value.
4.3. Alternate Address Trailer
The Alternate Address Trailer is used by the Hairpinning Extension.
The Alternate Address Trailer MUST NOT be present in any packets
other than indirect bubbles sent by a Teredo client. The Alternate
Address Trailer provides another Teredo client positioned behind the
same NAT with more address options that it can use to connect.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| |
| Alternate Address/Port List (variable) |
| |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Thaler Standards Track [Page 19]
RFC 6081 Teredo Extensions January 2011
Type (1 byte): The Trailer Option type. This field MUST be set to
0x03.
Length (1 byte): The length in bytes of the rest of the option. The
value of this field MUST be in the range 8 to 26 (i.e., 2 bytes for
the Reserved field, and 6 bytes for each entry in the Alternate
Address/Port List). This allows for a minimum of one address/port
mapping and a maximum of four address/port mappings to be advertised.
It SHOULD be at most 14 as a maximum of two address/port mappings can
be determined by Teredo: one local address/port and one obtained
using UPnP. Because the length of the alternate address/port is 6
bytes, the valid range of values is only 8, 14, 20, and 26.
Reserved (2 bytes): This field MUST be set to 0x0000 and ignored on
receipt.
Alternate Address/Port List (variable): An array of additional
address/port pairs that can be used by other Teredo clients to
communicate with the sender. Each alternate address/port entry MUST
be formatted as follows:
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| IPv4 Address |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Port |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
IPv4 Address (4 bytes): An IPv4 address in network byte order. This
field MUST contain a valid unicast address.
Port (2 bytes): A port number in network byte order. This field MUST
NOT be zero.
4.4. Neighbor Discovery Option Trailer
The Neighbor Discovery Option Trailer is used by the Server Load
Reduction Extension because it allows direct bubbles to encode an
IPv6 Neighbor Solicitation (Section 4.3 of [RFC4861]), in addition to
an IPv6 Neighbor Advertisement (Section 4.4 of [RFC4861]). This
allows packets to be sent without having to relay them through a
Teredo server. The Neighbor Discovery Option Trailer allows the
receiver to differentiate between a direct bubble that is soliciting
a response versus a regular direct bubble. This allows Teredo
clients to use direct bubbles to refresh inactive connections instead
of using indirect bubbles.
Thaler Standards Track [Page 20]
RFC 6081 Teredo Extensions January 2011
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | DiscoveryType | Reserved |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| ... |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type (1 byte): The Trailer Option type. This field MUST be set to
0x04.
Length (1 byte): The length in bytes of the rest of the option. This
field MUST be set to 0x04.
DiscoveryType (1 byte): This field MUST be set to one of the
following values:
TeredoDiscoverySolicitation (0x00): The receiver is requested to
respond with a direct bubble of DiscoveryType
TeredoDiscoveryAdvertisement.
TeredoDiscoveryAdvertisement (0x01): The direct bubble is in
response to a direct bubble or an indirect bubbles containing
DiscoveryType TeredoDiscoverySolicitation.
Reserved (3 bytes): This field MUST be set to 0x000000 on
transmission and ignored on receipt.
4.5. Random Port Trailer
The Random Port Trailer is used by the Port-Preserving Symmetric NAT
Extension in both indirect and direct bubbles.
1 2 3
0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 1
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
| Type | Length | Random Port |
+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+
Type (1 byte): The Trailer Option type. This field MUST be set to
0x05.
Length (1 byte): The length in bytes of the rest of the option. This
field MUST be set to 0x02.
Random Port (2 bytes): The external port that the sender predicts
that its NAT has assigned it for communication with the destination.
This field MUST be specified in network byte order.
Thaler Standards Track [Page 21]
RFC 6081 Teredo Extensions January 2011
5. Protocol Details
5.1. Common Processing
The behavior in this section applies to multiple extensions.
Packets equivalent to those sent for a peer the first time a
connection is being established MAY be generated at other
implementation-specific times. (For example, an implementation might
choose to do so when its Neighbor Cache Entry for the peer is in the
PROBE state.)
5.1.1. Refresh Interval
Section 5.2 of [RFC4380] states:
The client must regularly perform the maintenance procedure in
order to guarantee that the Teredo service port remains usable.
The need to use this procedure or not depends on the delay since
the last interaction with the Teredo server. The refresh
procedure takes as a parameter the "Teredo refresh interval".
This parameter is initially set to 30 seconds; it can be updated
as a result of the optional "interval determination procedure".
The randomized refresh interval is set to a value randomly chosen
between 75% and 100% of the refresh interval.
This requirement can be problematic when the client is behind a NAT
that expires state in less than 30 seconds. The optional interval
determination procedure (Section 5.2.7 of [RFC4380]) also does not
provide for intervals under 30 seconds. Hence, this document refines
the behavior by saying the initial parameter SHOULD be configurable
and the default MUST be 30 seconds. An implementation MAY set the
randomized refresh interval to a value randomly chosen within an
implementation-specific range. Such a range MUST fall within 50% to
150% of the refresh interval.
Section 5.2.5 of [RFC4380] states that:
At regular intervals, the client MUST check the "date and time of
the last interaction with the Teredo server" to ensure that at
least one packet has been received in the last Randomized Teredo
Refresh Interval. If this is not the case, the client SHOULD send
a router solicitation message to the server, as specified in
Section 5.2.1;
Thaler Standards Track [Page 22]
RFC 6081 Teredo Extensions January 2011
This document refines the behavior as follows. A Teredo client MAY
choose to send additional router solicitation messages to the server
at other implementation-specific times. (For example, an
implementation might choose to do so when its Neighbor Cache Entry
for the router is in the PROBE state.)
5.1.2. Trailer Processing
A Teredo client MUST process the sequence of trailers in the same
order as they appear in the packet. If the Teredo client does not
recognize the trailer Type while processing the trailers in the
Teredo packet, the client MUST discard the packet if the highest-
order bits of the trailer Type contain 01, or else the Teredo client
MUST skip past the trailer. A Teredo client MUST stop processing the
trailers as soon as a malformed trailer appears in the sequence of
trailers in the packet. A trailer is defined as malformed if it has
any of the following properties:
o The length in bytes of the remainder of the UDP datagram is less
than 2 (the size of the Type and Length fields of a trailer).
o The length in bytes of the remainder of the UDP datagram is less
than 2 + the value of the Length field of the trailer.
5.2. Symmetric NAT Support Extension
Section 5.2.1 of [RFC4380] advises that no Teredo IPv6 address be
configured if the Teredo client is positioned behind a symmetric NAT.
For Teredo clients positioned behind symmetric NATs, the mapped
address/port used by its NAT when communicating with a Teredo peer is
different from the mapped address/port embedded in the Teredo
client's Teredo IPv6 address. The Symmetric NAT Support Extension
provides a solution to this problem.
In addition, Section 5.2.9 of [RFC4380] specifies a direct IPv6
connectivity test to determine that the mapped address/port in the
Teredo IPv6 address of a peer is not spoofed. It does this through
the use of a nonce in ICMPv6 Echo Request and Response messages
(which are defined in Section 4 of [RFC4443]). However, the direct
IPv6 connectivity test is limited only to communication between
Teredo IPv6 addresses and non-Teredo IPv6 addresses. In the
following extension, we introduce the use of a nonce in direct and
indirect bubbles and provide a mechanism to verify that the mapped
address/port are not spoofed.
This extension is optional; an implementation SHOULD support it.
Thaler Standards Track [Page 23]
RFC 6081 Teredo Extensions January 2011
5.2.1. Abstract Data Model
This section describes a conceptual model of possible data
organization that an implementation maintains to participate in this
protocol. The described organization is provided to facilitate the
explanation of how the protocol behaves. This document does not
mandate that implementations adhere to this model as long as their
external behavior is consistent with that described in this document.
In addition to the state specified in Section 5.2 of [RFC4380], the
following are also required.
Peer Entry: The following additional state is required on a per-peer
basis:
o Nonce Sent: The value of the nonce sent in the last indirect
bubble sent to the Teredo peer.
o Nonce Received: The value of the nonce received in the last
indirect bubble received from the Teredo peer.
5.2.2. Timers
No timers are necessary other than those in [RFC4380].
5.2.3. Initialization
No initialization is necessary other than that specified in
[RFC4380].
5.2.4. Message Processing
Except as specified in the following sections, the rules for message
processing are as specified in [RFC4380].
5.2.4.1. Sending an Indirect Bubble
The rules for when indirect bubbles are sent to a Teredo peer are
specified in Section 5.2.6 of [RFC4380]. When a Teredo client sends
an indirect bubble, it MUST generate a random 4-byte value and
include it in the Nonce field of a Nonce Trailer (Section 4.2)
appended to the indirect bubble, and also store it in the Nonce Sent
field of its Peer Entry for that Teredo peer.
Thaler Standards Track [Page 24]
RFC 6081 Teredo Extensions January 2011
5.2.4.2. Sending a Direct Bubble
The rules for when direct bubbles are sent to a Teredo peer are
specified in Section 5.2.6 of [RFC4380]. When a Teredo client sends
a direct bubble to a peer after receiving an indirect bubble with a
Nonce Trailer, it MUST include in the direct bubble a Nonce Trailer
with the same nonce value.
If the Teredo client is about to send a direct bubble before it has
received an indirect bubble from the Teredo peer, the Teredo client
MUST NOT include a Nonce Trailer.
5.2.4.3. Receiving an Indirect Bubble
The rules for processing an indirect bubble are specified in Section
5.2.3 of [RFC4380]. In addition, when a Teredo client receives an
indirect bubble containing a Nonce Trailer, the Teredo client MUST
store the nonce in the Nonce Received field of its Peer Entry for
that Teredo peer. If an indirect bubble is received without a Nonce
Trailer, and the Nonce Received field in the Peer Entry is non-zero,
the Nonce Received field SHOULD be set to zero.
5.2.4.4. Receiving a Direct Bubble
If the mapped address/port of the direct bubble matches the mapped
address/port embedded in the source Teredo IPv6 address, the direct
bubble MUST be accepted, as specified in Section 5.2.3 of [RFC4380].
In addition, if the mapped address/port does not match the embedded
address/port but the direct bubble contains a Nonce Trailer with a
nonce that matches the Nonce Sent field of the Teredo peer, the
direct bubble MUST be accepted.
If neither of the above conditions is true, the direct bubble MUST be
dropped.
If the direct bubble is accepted, the Teredo client MUST record the
mapped address/port from which the direct bubble is received in the
mapped address/port fields of the Teredo peer, as specified in
Section 5.2 of [RFC4380].
5.3. UPnP-Enabled Symmetric NAT Extension
The UPnP-enabled Symmetric NAT Extension is optional; an
implementation SHOULD support it. This extension has the Symmetric
NAT Support Extension (Section 5.2) as a dependency. Any node that
implements this extension MUST also implement the Symmetric NAT
Support Extension.
Thaler Standards Track [Page 25]
RFC 6081 Teredo Extensions January 2011
5.3.1. Abstract Data Model
This section describes a conceptual model of possible data
organization that an implementation maintains to participate in this
protocol. The described organization is provided to facilitate the
explanation of how the protocol behaves. This document does not
mandate that implementations adhere to this model as long as their
external behavior is consistent with that described in this document.
This extension extends the abstract data model in Section 5.2.1 by
adding the following additional fields.
UPnP-Enabled NAT flag: This is a Boolean value, set to TRUE if the
NAT positioned in front of the Teredo client is UPnP enabled. The
default value of this flag is FALSE.
UPnP-Mapped Address/Port: The mapped address/port assigned via UPnP
to the Teredo client by the UPnP-enabled NAT behind which the Teredo
client is positioned. Note that this field has a valid value only if
the NAT to which the Teredo client is connected is UPnP enabled.
Also, note that if the Teredo client is positioned behind a single
NAT only (as opposed to a series of nested NATs), this value is the
same as the mapped address/port embedded in its Teredo IPv6 address.
Symmetric NAT flag: This is a Boolean value, set to TRUE if the
Teredo client is positioned behind a symmetric NAT.
Peer Entry: The following state needs to be added on a per-peer
basis:
o Symmetric Peer flag: This is a Boolean value and is TRUE if the
Teredo peer is positioned behind a symmetric NAT.
A Teredo client SHOULD also maintain the following state that is
persisted across reboots:
o Persisted UPnP-Mapped Port: The mapped port assigned via UPnP to
the Teredo client by the UPnP-enabled NAT behind which the Teredo
client is positioned. Note that this value is the same as the
UPnP-Mapped Port value when both are non-zero. The default value
is all zero bytes.
5.3.2. Timers
No timers are necessary other than those in [RFC4380].
Thaler Standards Track [Page 26]
RFC 6081 Teredo Extensions January 2011
5.3.3. Initialization
Prior to beginning the qualification procedure, the Teredo client
MUST first perform the uninitialization procedure specified in
Section 5.3.5.1 if the Persisted UPnP-Mapped Port is supported and
non-zero.
The Teredo client MUST then invoke the AddPortMapping function, as
specified in Section 2.4.16 of [UPNPWANIP], with the following
parameters:
o NewRemoteHost: "" (empty string)
o NewExternalPort: Local Port value
o NewProtocol: UDP
o NewInternalPort: Local Port value
o NewInternalClient: Local Address value
o NewEnabled: TRUE
o NewPortMappingDescription: "TEREDO"
o NewLeaseDuration: 0
The successful completion of the AddPortMapping function indicates
that the NAT has created a port mapping from the external port of the
NAT to the internal port of the Teredo client node. The parameters
are specified so that any external host should be able to send
packets to the Teredo client by sending packets to the mapped
address/port. If the AddPortMapping function fails, the Teredo
client MUST continue without using this extension. Otherwise, it
MUST proceed as follows.
The Teredo client MUST set the UPnP-Mapped Port (and Persisted UPnP-
Mapped Port, if supported) to the Local Port value specified in
AddPortMapping. The Teredo client MUST then call the
GetExternalIPAddress function specified in Section 2.4.18 of
[UPNPWANIP]. If the GetExternalIPAddress function fails, the Teredo
client SHOULD perform the uninitialization procedure specified in
Section 5.3.5.1 and continue without using this extension. If the
GetExternalIPAddress function succeeds, the Teredo client MUST
proceed as follows.
Thaler Standards Track [Page 27]
RFC 6081 Teredo Extensions January 2011
The Teredo client MUST set the UPnP-Mapped Address to the address
returned from the GetExternalIPAddress function, and set the UPnP-
Enabled NAT flag to TRUE.
During the qualification procedure (as specified in Section 5.2.1 of
[RFC4380]) when the Teredo client receives a response from the
secondary Teredo server, the Teredo client MUST compare the mapped
address/port learned from the secondary Teredo server with the mapped
address/port associated with the Teredo server. If either the mapped
address or the mapped port value is different, the Symmetric NAT flag
MUST be set to TRUE.
After the qualification procedure, the mapped address/port learned
from the Teredo server MUST be compared to the UPnP-Mapped Address/
Port. If both are the same, the Teredo client is positioned behind a
single NAT and the UPnP-Mapped Address/Port MUST be zeroed out.
5.3.4. Message Processing
Except as specified in the following sections, the rules for message
processing are as specified in Section 5.2.3 of [RFC4380].
5.3.4.1. Receiving a Direct Bubble
Except as indicated below, the rules for handling a direct bubble are
as specified in Section 5.2.4.4.
A Teredo client positioned behind a UPnP-enabled NAT (port-restricted
NAT as well as symmetric NAT) will receive all packets sent to the
mapped address/port embedded in its Teredo IPv6 address. Thus, when
a Teredo client receives a direct bubble, it MUST compare the mapped
address/port from which the packet was received with the mapped
address/port embedded in the Teredo IPv6 address in the source
address field of the IPv6 header. If the two are not the same, it
indicates that the Teredo peer is positioned behind a symmetric NAT,
and it MUST set the Symmetric Peer flag in its Peer Entry.
5.3.4.2. Sending a Direct Bubble
The rules for sending a direct bubble are specified in Section 5.2.6
of [RFC4380] and Section 5.2.4.2 of this document. These rules are
further refined as follows.
If the Teredo client sending the direct bubble meets all of the
following criteria:
o The Symmetric NAT flag is set to TRUE.
Thaler Standards Track [Page 28]
RFC 6081 Teredo Extensions January 2011
o The UPnP-Enabled NAT flag is set to TRUE.
o The UPnP-Mapped Address/Port are set to zero.
o The peer's Symmetric Peer flag is set to TRUE.
then the Teredo client MUST send the direct bubble to the mapped
address/port embedded in the peer's Teredo IPv6 address.
This is because Symmetric-to-Symmetric and Port-Restricted-to-
Symmetric NAT communication between the Teredo client and the peer
would have failed anyway. However, by taking a chance that the peer
might also be positioned behind a UPnP-enabled NAT just like the
Teredo client itself, the Teredo client can try sending the direct
bubble to the mapped address/port in the peer's Teredo IPv6 address.
If the packet does go through, communication is established.
5.3.4.3. Sending a Data Packet
The rules for sending a data packet are specified in Section 5.2.4 of
[RFC4380]. These rules are further refined as follows.
If the Teredo client sending the data packet meets all of the
following criteria:
o The Symmetric NAT flag is set to TRUE.
o The UPnP-Enabled NAT flag is set to TRUE.
o The UPnP-Mapped Address/Port are set to zero.
o The peer's Symmetric Peer flag is set to TRUE.
then the Teredo client MUST send the data packet to the mapped
address/port embedded in the peer's Teredo IPv6 address.
5.3.5. Shutdown
When Teredo client functionality is being shut down, uninitialization
MUST be performed as specified in Section 5.3.5.1.
5.3.5.1. Uninitialization
First determine the mapped port as follows. If Persisted UPnP-Mapped
Port is supported, use it as the mapped port. Otherwise, use the
UPnP-Mapped Port.
Thaler Standards Track [Page 29]
RFC 6081 Teredo Extensions January 2011
If the mapped port is non-zero, the Teredo client MUST call the
DeletePortMapping function, as specified in Section 2.4.17 of
[UPNPWANIP], with the following parameters:
o NewRemoteHost: "" (empty string)
o NewExternalPort: the mapped port
o NewProtocol: UDP
5.4. Port-Preserving Symmetric NAT Extension
The Port-Preserving Symmetric NAT Extension is optional; an
implementation SHOULD support it. This extension has the Symmetric
NAT Support Extension (as specified in Section 5.2) as a dependency.
Any node that implements this extension MUST also implement the
Symmetric NAT Support Extension.
5.4.1. Abstract Data Model
This section describes a conceptual model of possible data
organization that an implementation maintains to participate in this
protocol. The described organization is provided to facilitate the
explanation of how the protocol behaves. This document does not
mandate that implementations adhere to this model as long as their
external behavior is consistent with that described in this document.
The Port-Preserving Symmetric NAT Extension extends the abstract data
model in Section 5.2.1 by adding the following additional fields.
Port-Preserving NAT flag: This is a Boolean value, set to TRUE if the
Teredo client is positioned behind a port-preserving NAT.
Symmetric NAT flag: This is a Boolean value, set to TRUE if the
Teredo client is positioned behind a symmetric NAT.
Peer Entry: The following fields need to be added on a per-peer
basis:
o Random Port: This field contains the value of the external port
that the Teredo client predicts that its NAT has assigned it for
communication with the peer. Set to zero by default.
o Peer Random Port: This field contains the value of the random port
that the peer is using for communication with this Teredo client.
Set to zero by default.
Thaler Standards Track [Page 30]
RFC 6081 Teredo Extensions January 2011
o Direct Receive on Primary Port: This is a Boolean value, set to
TRUE if a packet is received from the Teredo peer on the primary
local port. Set to FALSE by default.
o Direct Receive on Random Port: This is a Boolean value, set to
TRUE if a packet is received from the Teredo peer on the Random
Port. Set to FALSE by default.
o Connection Refresh Count: This field contains the number of direct
bubbles that have been sent to the peer since the last time data
was sent to the peer.
o Last Data Packet Sent Timestamp: This field contains the timestamp
of the last data packet sent to the peer. This timestamp is
different from the field that stores the data and time of last
transmission to the peer (as specified in Section 5.2 of
[RFC4380]) because the RFC-defined field is also updated every
time a direct bubble is sent.
5.4.2. Timers
Other than those in [RFC4380], the Port-Preserving Symmetric NAT
Extension requires the following additional timer.
Peer Refresh Timer: A timer to refresh peer connections through the
random port, on which no data has been sent for a while.
5.4.2.1. Peer Refresh Timer Expiry
When the Peer Refresh Timer expires, the Teredo client MUST go
through its list of peers and for each peer to which the Teredo
client is communicating through the random port, the Teredo client
MUST check the Last Data Packet Sent Timestamp to determine if data
has been sent to the peer in the last 30 seconds, and check the
Connection Refresh Count field to determine if the count has reached
the maximum allowed value of 20. If both checks are FALSE, the
Teredo client MUST send a direct bubble (as specified in
Section 5.4.4.3) to the peer and increment the Connection Refresh
Count. This direct bubble is sent as an attempt to keep the port
mappings on all the intermediate NATs alive while the application/
user may be temporarily inactive. If on the other hand, data has
been sent to the peer in the last 30 seconds, the Connection Refresh
Count MUST be reset to zero.
The Peer Refresh Timer MUST then be rescheduled to expire in 30
seconds.
Thaler Standards Track [Page 31]
RFC 6081 Teredo Extensions January 2011
5.4.3. Initialization
In addition to the behavior specified in [RFC4380], the Port-
Preserving NAT flag and Symmetric NAT flag MUST be set to FALSE when
the Teredo client is started. The Peer Refresh Timer MUST be started
and scheduled to expire in 30 seconds.
During the qualification procedure (as specified in Section 5.2.1 of
[RFC4380]), when the Teredo client receives a response from the
Teredo server address, the Teredo client MUST compare the Port value
in the origin indication, as specified in Section 5.1.1 of [RFC4380],
with the Local Port value. If both values match, the client MUST set
the Port-Preserving NAT flag to TRUE.
5.4.4. Message Processing
5.4.4.1. Sending a Data Packet
On receiving a data packet to be transmitted to the Teredo peer (in
addition to the rules specified in Section 5.2.4 of [RFC4380]), the
Teredo client MUST update the Last Data Packet Sent Timestamp when
the packet is actually sent.
5.4.4.2. Sending an Indirect Bubble
The rules for sending an indirect bubble are as specified in
Section 5.2.4.1 of this document and Section 5.2.6 of [RFC4380]. In
addition to those rules, if the Port-Preserving NAT flag is TRUE, the
Teredo client MUST do the following:
o If the Symmetric NAT flag is set, the Teredo peer is not marked as
"trusted" (as specified in Section 5.2 of [RFC4380]), and the
Random Port is zero, the Teredo client MUST first select a random
port number to use, and then begin listening on that port. Since
the NAT is port-preserving, the Teredo client can predict that the
external port assigned will be equal to the random port chosen,
and hence the Teredo client MUST store the random port chosen in
the Random Port field of the Peer Entry.
o If the Random Port value is non-zero, the Teredo client MUST
append a Random Port Trailer to the indirect bubble.
Thaler Standards Track [Page 32]
RFC 6081 Teredo Extensions January 2011
5.4.4.3. Sending a Direct Bubble
The rules for when direct bubbles are sent to a Teredo peer are as
specified in Section 5.2.6 of [RFC4380]. In addition,
Section 5.2.4.2 defines rules for enabling communication for clients
positioned behind a symmetric NAT. In addition to the rules defined
in both the aforementioned sections, if the Port-Preserving NAT flag
is TRUE, the following rules apply also.
If the Symmetric NAT flag is set, and the Teredo peer is not marked
as "trusted" (as specified in Section 5.2 of [RFC4380]) the Teredo
client MUST send a direct bubble destined to the mapped address/port
embedded in the Teredo IPv6 address of the Teredo peer. If the peer
Random Port field is non-zero, the Teredo client MUST send another
direct bubble from its own random port, destined to the peer random
port. The IPv4 destination address MUST be the mapped address
embedded in the Teredo IPv6 address. In addition, the Teredo client
MUST include the Random Port Trailer (Section 4.5).
5.4.4.4. Receiving an Indirect Bubble
The rules for processing an indirect bubble are as specified in
Section 5.2.4.3 of this document and Section 5.2.3 of [RFC4380]. In
addition to these rules, if the incoming indirect bubble has a Random
Port Trailer, the following additional processing MUST be done.
If the Peer Random Port field of the Peer Entry is zero, the Teredo
client MUST store the port from the Random Port Trailer in the Peer
Random Port field of the Peer Entry.
If the Peer Random Port field is non-zero and if either the Peer
Random Port field and the new advertised port have the same value, or
if active data has been exchanged between the two Teredo clients in
the last 30 seconds (that is, "time of last transmission" or "time of
last reception", as specified in Section 5.2 of [RFC4380], is set to
a time that is less than 30 seconds ago), the new advertised port
value MUST be ignored.
If the Peer Random Port field is non-zero and the new advertised port
value is different from the Peer Random Port value, and it has been
more than 30 seconds since the last exchange of data packets between
the two Teredo clients, (that is, "time of last transmission" and
"time of last reception" are set to a time that is more than 30
seconds ago), the Teredo client SHOULD store the new advertised port
value in the Peer Random Port field and, if the Port-Preserving NAT
flag is TRUE, then clear the Random Port field, and stop listening on
the old random port. This allows communication to be re-established
if either side changes the random port that it is using.
Thaler Standards Track [Page 33]
RFC 6081 Teredo Extensions January 2011
5.4.4.5. Receiving a Direct Bubble
The rules for handling direct bubbles are specified in
Section 5.2.4.4 of this document and Section 5.2.3 of [RFC4380]. The
rules for whether to accept a direct bubble are extended as follows,
when the Port-Preserving NAT flag is TRUE:
o If the direct bubble is received on the primary port and the
Teredo peer is not "trusted", the status field of the Teredo
client MUST be changed to "trusted" and the Direct Receive on
Primary Port flag MUST be set to TRUE. The mapped address/port
from which the direct bubble was received MUST be recorded in the
mapped address/port fields of the Teredo peer, as specified in
Section 5.2 of [RFC4380]. The Teredo client MUST then set the
Random Port field in the Peer Entry to zero and stop listening on
the old random port.
o If the direct bubble is received on the primary port, the Teredo
peer is "trusted", and the Direct Receive on Primary flag is set
to TRUE, the Teredo client MUST compare the mapped address/port of
the direct bubble with the mapped address/port of the Peer Entry.
If both mappings are the same, the direct bubble MUST be accepted.
If the mappings are different and it has been more than 30 seconds
since the last packet exchange with the Teredo peer (that is,
"time of last transmission" and "time of last reception", as
defined in Section 5.2 of [RFC4380], are set to a time that is
more than 30 seconds ago), the mapping on the Teredo peer's NAT
has changed and communication needs to be re-established. This
MUST be done by changing the status of the peer to "not-trusted",
setting the Direct Receive on Primary Port flag to FALSE, and
sending an indirect bubble to the Teredo peer via its Teredo
server.
o If the direct bubble is received on the primary port, the Teredo
peer is "trusted", the Direct Receive on Primary Port flag is set
to FALSE, and the Direct Receive on Random Port flag is set to
TRUE, the mapped address/port from which the direct bubble is
received MUST be stored in the mapped address/port fields of the
Peer Entry. The Direct Receive on Primary Port flag MUST be set
to TRUE. The Teredo client MUST then set the Random Port field in
the Peer Entry to zero and stop listening on the old random port.
Finally, the Direct Receive on Random Port flag MUST be set to
FALSE.
Thaler Standards Track [Page 34]
RFC 6081 Teredo Extensions January 2011
o If the direct bubble is received on the random port and the Teredo
peer is not "trusted", the status field of the Teredo client MUST
be changed to "trusted" and the Direct Receive on Random Port flag
MUST be set to TRUE. The mapped address/port from which the
direct bubble was received MUST be recorded in the mapped address/
port fields of the Teredo Peer Entry, as specified in Section 5.2
of [RFC4380].
o If the direct bubble is received on the random port, the Teredo
peer is "trusted", and the Direct Receive on Primary Port flag is
FALSE, the Teredo client MUST compare the mapped address/port in
the direct bubble with the mapped address/port in the Peer Entry.
If the two mappings are the same, the direct bubble MUST be
accepted. If the mappings are different, it implies that the NAT
had deleted the mapping and when it reassigned the mapping, a
different external port was chosen. In this instance, the Teredo
client SHOULD set the Random Port field to zero, stop listening on
the old random port, and send an indirect bubble to the Teredo
peer as specified in Section 5.4.4.2.
Note that once the Direct Receive on Primary Port flag is TRUE, the
client will stop listening on the random port and hence a direct
bubble cannot be received on the random port. As a result, this case
is intentionally omitted above.
5.5. Sequential Port-Symmetric NAT Extension
The Sequential Port-Symmetric NAT Extension is optional; an
implementation SHOULD support it. This extension has the Symmetric
NAT Support Extension (Section 5.2) as a dependency. Any node that
implements this extension MUST also implement the Symmetric NAT
Support Extension, as well as the Port-Preserving NAT Extension
(Section 5.4).
5.5.1. Abstract Data Model
This section describes a conceptual model of possible data
organization that an implementation maintains to participate in this
protocol. The described organization is provided to facilitate the
explanation of how the protocol behaves. This document does not
mandate that implementations adhere to this model as long as their
external behavior is consistent with that described in this document.
The Sequential Port-Symmetric NAT Extension extends the abstract data
model in Section 5.4.1 by adding the following additional state.
Thaler Standards Track [Page 35]
RFC 6081 Teredo Extensions January 2011
Peer Entry: The following fields need to be added on a per-peer
basis:
o EchoTestNonce1: The value of the nonce sent as part of the
authentication encapsulation, as specified in Section 5.1.1 of
[RFC4380], in the router solicitation packet sent to the Teredo
server address as part of the Echo Test.
o EchoTestNonce2: The value of the nonce sent as part of the
authentication encapsulation in the router solicitation packet
sent to the secondary Teredo server address as part of the Echo
Test.
o EchoTestLowerPort: The value of the external port mapping
extracted from the origin indication of the router advertisement
received from the Teredo server address as part of the Echo Test.
A value of 0 indicates that no such router advertisement has been
received.
o EchoTestUpperPort: The value of the external port mapping
extracted from the origin indication of the router advertisement
received from the secondary Teredo server address as part of the
Echo Test. A value of 0 indicates that no such router
advertisement has been received.
o EchoTestRetryCounter: The number of times an Echo Test has been
attempted.
5.5.2. Timers
In addition to the timers specified in Section 5.4.2, the following
additional timer is required per Peer Entry.
Echo Test Failover Timer: A one-shot timer that runs whenever an Echo
Test is in progress.
5.5.2.1. Peer Refresh Timer Expiry
The processing of the Peer Refresh Timer Expiry MUST be completed as
specified in Section 5.4.2.1. In addition to those rules, the Teredo
client MUST set the EchoTestLowerPort, EchoTestUpperPort, and
EchoTestRetryCounter to zero.
5.5.2.2. Echo Test Failover Timer Expiry
If the Echo Test Failover Timer expires, the Teredo client MUST do
the following.
Thaler Standards Track [Page 36]
RFC 6081 Teredo Extensions January 2011
If the value of the EchoTestRetryCounter is two, then the Teredo
client MUST send an indirect bubble as specified in Section 5.2.4.1.
If the value of the EchoTestRetryCounter is one, then the Teredo
client MUST start another Echo Test as specified in
Section 5.5.4.1.1.
5.5.3. Initialization
No behavior changes are required beyond what is specified in
Section 5.4.3.
5.5.4. Message Processing
Except as specified in the following sections, the rules for message
processing are as specified in Section 5.4.4.
5.5.4.1. Handling a Request to Send an Indirect Bubble
Whenever [RFC4380] or other extensions specified in this document
specify that an indirect bubble is to be sent, the following actions
apply at that time instead if the Symmetric NAT flag is TRUE and the
Port-Preserving NAT flag is FALSE. Note that any behavior specified
by [RFC4380] or other extensions in this document still applies to
how indirect bubbles are constructed, but such behavior is done at a
later time as specified in Section 5.5.4.4.
If the Symmetric NAT flag is TRUE, and the Port-Preserving NAT flag
is FALSE, and the Teredo peer is not marked as "trusted" (as
specified in Section 5.2 of [RFC4380]), and the Random Port is zero,
then the Teredo client MUST select a random port number to use, begin
listening on that port, and start an Echo Test as specified below.
5.5.4.1.1. Starting an Echo Test
To start an Echo Test, the Teredo client MUST send the following
three packets from this port:
o First, a router solicitation (as specified in Section 5.2.1 of
[RFC4380]) MUST be sent to the Teredo server address. The router
solicitation MUST include an authentication encapsulation with a
randomly generated Nonce field, as specified in Section 5.1.1 of
[RFC4380]. The nonce included in the authentication encapsulation
MUST then be stored in the EchoTestNonce1 field of the Peer Entry.
o Second, a direct bubble MUST be sent to the peer.
Thaler Standards Track [Page 37]
RFC 6081 Teredo Extensions January 2011
o Third, a router solicitation MUST be sent to the secondary Teredo
server address. The router solicitation MUST include an
authentication encapsulation with a randomly generated Nonce
field, as specified in Section 5.1.1 of [RFC4380]. The nonce
included in the authentication encapsulation MUST then be stored
in the EchoTestNonce2 field of the Peer Entry.
The Teredo client MUST then increment the EchoTestRetryCounter and
set the Echo Test Failover Timer to expire in a number of seconds
equal to EchoTestRetryCounter.
5.5.4.2. Sending an Indirect Bubble
The rules for sending an indirect bubble are as specified in
Section 5.2.4.1 of this document and Section 5.2.6 of [RFC4380]. In
addition to those rules, if the Symmetric NAT flag is TRUE, and the
Port-Preserving NAT flag is FALSE, and the Random Port value is non-
zero, then the Teredo client MUST append a Random Port Trailer to the
indirect bubble.
5.5.4.3. Receiving a Direct Bubble
The processing of the direct bubble MUST be completed as specified in
Section 5.4.4.5, as if the Port-Preserving NAT flag were TRUE. After
the processing is complete, if the Direct Bubble Received on Primary
flag is TRUE, and the Echo Test Failover Timer is running, then the
Echo Test Failover Timer MUST be canceled and EchoTestLowerPort,
EchoTestUpperPort, and EchoTestRetryCounter MUST be set to zero.
5.5.4.4. Receiving a Router Advertisement
The rules for processing a router advertisement are as specified in
Section 5.2.1 of [RFC4380]. In addition to those rules, if the
router advertisement contains an authentication encapsulation, the
Teredo client MUST look for a Peer Entry whose EchoTestNonce1 or
EchoTestNonce2 field matches the nonce in the authentication
encapsulation. If a Peer Entry is found, the Teredo client MUST do
the following.
If the received nonce is equal to EchoTestNonce1 and
EchoTestLowerPort is zero, then EchoTestLowerPort MUST be set to the
external port mapping extracted from the origin indication of this
router advertisement.
If the received nonce is equal to EchoTestNonce2 and
EchoTestUpperPort is zero, then EchoTestUpperPort MUST be set to the
external port mapping extracted from the origin indication of this
router advertisement.
Thaler Standards Track [Page 38]
RFC 6081 Teredo Extensions January 2011
If the EchoTestUpperPort and EchoTestLowerPort are now both non-zero,
the Teredo client MUST then set the Random Port field of the Peer
Entry to (EchoTestUpperPort + EchoTestUpperPort)/2, rounded down, and
send an indirect bubble as specified in Section 5.5.4.2.
5.6. Hairpinning Extension
This extension is optional; an implementation SHOULD support it.
5.6.1. Abstract Data Model
This section describes a conceptual model of possible data
organization that an implementation maintains to participate in this
protocol. The described organization is provided to facilitate the
explanation of how the protocol behaves. This document does not
mandate that implementations adhere to this model as long as their
external behavior is consistent with that described in this document.
In addition to the state specified in Section 5.2 of [RFC4380], the
following are also required:
UPnP Mapped Address/Port: The mapped address/port assigned via UPnP
to the Teredo client by the UPnP-enabled NAT behind which the Teredo
client is positioned. This field has a valid value only if the NAT
to which the Teredo client is connected is UPnP enabled. In
addition, if the Teredo client is positioned behind a single NAT only
(as opposed to a series of nested NATs), this value will be the same
as the mapped address/port embedded in its Teredo IPv6 address.
Peer Entry: Per-peer state is extended beyond what is described in
[RFC4380] by including the following:
o Alternate Address/Port list: The list of alternate address/port
pairs advertised by the peer.
5.6.2. Timers
No timers are necessary other than those in [RFC4380].
5.6.3. Initialization
Behavior is as specified in [RFC4380], with the following additions.
Prior to beginning the qualification procedure, the Teredo client
MUST invoke the AddPortMapping function (as specified in Section
2.4.16 of [UPNPWANIP]) with the parameters specified in
Section 5.3.3. If successful, it indicates that the NAT has created
a port mapping from the external port of the NAT to the internal port
Thaler Standards Track [Page 39]
RFC 6081 Teredo Extensions January 2011
of the Teredo client node. If the AddPortMapping function is
successful, the Teredo client MUST store the mapping assigned by the
NAT in its UPnP Mapped Address/Port state.
After the qualification procedure, the mapped address/port learned
from the Teredo server MUST be compared to the UPnP Mapped Address/
Port. If both are the same, the Teredo client is positioned behind a
single NAT and the UPnP Mapped Address/Port MUST be zeroed out.
5.6.4. Message Processing
5.6.4.1. Sending an Indirect Bubble
The rules for when indirect bubbles are sent to a Teredo peer are as
specified in Section 5.2.6 of [RFC4380]. If communication between a
Teredo client and a Teredo peer has not been established, the Teredo
client MUST include the Alternate Address Trailer in the indirect
bubble. The Alternate Address Trailer MUST include the node's local
address/port in the Alternate Address/Port list. If the UPnP Mapped
Address/Port is non-zero, the Alternate Address Trailer MUST also
include it in the list.
Hairpinning requires "direct IPv6 connectivity tests" (as specified
in Section 5.2.9 of [RFC4380]) to succeed before it can accept
packets from an IPv4 address and port not embedded in the Teredo IPv6
address. Hence, the indirect bubble MUST also include a Nonce
Trailer.
5.6.4.2. Receiving an Indirect Bubble
The rules for processing indirect bubbles are as specified in Section
5.2.3 of [RFC4380]. In addition to those rules, when a Teredo client
receives an indirect bubble with the Alternate Address Trailer, it
SHOULD first verify that the Alternate Address Trailer is correctly
formed (as specified in Section 4.3), and drop the bubble if not.
Otherwise, it MUST set the Alternate Address/Port list in its Peer
Entry to the list in the trailer. The Teredo client, besides sending
direct bubbles to the mapped address/port embedded in the Teredo IPv6
address (as specified in Section 5.2.6 of [RFC4380]), MUST also send
a direct bubble to each mapped address/port advertised in the
Alternate Address Trailer.
In each of the direct bubbles, the Teredo client MUST include a Nonce
Trailer with the nonce value received in the indirect bubble.
Thaler Standards Track [Page 40]
RFC 6081 Teredo Extensions January 2011
5.6.4.3. Receiving a Direct Bubble
If the mapped address/port of the direct bubble matches the mapped
address/port embedded in the source Teredo IPv6 address, the direct
bubble MUST be accepted, as specified in Section 5.2.3 of [RFC4380].
If the mapped address/port does not match the embedded address/port,
but the direct bubble contains a Nonce Trailer with a nonce that
matches the Nonce Sent field of the Teredo peer, the direct bubble
MUST be accepted.
If neither of the above rules match, the direct bubble MUST be
dropped.
5.7. Server Load Reduction Extension
This extension is optional; an implementation SHOULD support it.
5.7.1. Abstract Data Model
This section describes a conceptual model of possible data
organization that an implementation maintains to participate in this
protocol. The described organization is provided to facilitate the
explanation of how the protocol behaves. This document does not
mandate that implementations adhere to this model as long as their
external behavior is consistent with that described in this document.
In addition to the state specified in Section 5.2 of [RFC4380], the
following are also required.
Peer Entry: The following state needs to be added on a per-peer
basis:
o Count of Solicitations Transmitted: The number of Solicitation
packets sent.
5.7.2. Timers
Retransmission Timer: A timer used to retransmit Teredo Neighbor
Solicitation packets.
When the retransmission timer expires, the Teredo client MUST
retransmit a direct bubble with a Neighbor Discovery Option Trailer,
and increment the Count of Solicitations Transmitted. If the count
is less than three, it MUST then reset the timer to expire in two
seconds. Otherwise (if the count is now three), it MUST send an
Thaler Standards Track [Page 41]
RFC 6081 Teredo Extensions January 2011
indirect bubble to the Teredo peer to re-establish connectivity as if
no communication between the Teredo client and the Teredo peer had
been established.
5.7.3. Initialization
No initialization is necessary other than that specified in
[RFC4380].
5.7.4. Message Processing
Except as specified below, processing is the same as specified in
[RFC4380].
5.7.4.1. Sending a Data Packet
Upon receiving a data packet to be transmitted to the Teredo peer,
the Teredo client MUST determine whether data has been exchanged
between the Teredo client and peer in either direction in the last 30
seconds (using the state as specified in Section 5.2 of [RFC4380]).
If not, the Teredo client MUST send a direct bubble with a Neighbor
Discovery Option Trailer having the DiscoveryType field set to
TeredoDiscoverySolicitation. The Count of Solicitations Transmitted
field MUST be set to 1. The retransmission timer MUST be set to
expire in two seconds.
5.7.4.2. Receiving a Direct Bubble
The rules for processing direct bubbles are as specified in Section
5.2.3 of [RFC4380]. In addition to those rules, upon receiving a
direct bubble containing a Neighbor Discovery Option Trailer with
DiscoveryType field set to TeredoDiscoverySolicitation, the Teredo
client MUST respond with a direct bubble with the Neighbor Discovery
Option Trailer having the DiscoveryType field set to
TeredoDiscoveryAdvertisement.
6. Protocol Examples
The following sections describe several operations as used in common
scenarios to illustrate the function of Teredo Extensions.
6.1. Symmetric NAT Support Extension
The following protocol example illustrates the use of the Symmetric
NAT Support Extension.
Thaler Standards Track [Page 42]
RFC 6081 Teredo Extensions January 2011
In Figure 2 (Section 3.1), assume that Teredo Client A, which is
positioned behind a port-symmetric NAT, wants to communicate with
Teredo Client B, which is positioned behind an address-restricted
NAT.
The qualification procedure where the Teredo client determines that
it is positioned behind a symmetric NAT is exactly the same as that
specified in Section 5.2.1 of [RFC4380]. Because of the Symmetric
NAT Extension, Client A continues to configure a Teredo IPv6 address
even after determining that the Teredo client is positioned behind a
symmetric NAT.
Next the following packet exchange helps Teredo Client A (A)
establish communication with Teredo Client B (B).
Teredo Client A's Client B's Teredo
Client Teredo Teredo Client
A NAT Server Server NAT B
| | | | | |
| | | Direct Bubble to B | | |
1 |--------------------------------------------------->| |
| | | | | |
|Indirect Bubble to B via B's Teredo Server| | |
2 |----------------------------------------->|----------------->|
| | | | | |
| | | Direct Bubble to A | | |
| |<--------------------------------------------------| 3
| | | | | |
| | |Indirect Bubble to A via A's Teredo Server|
|<-----------------|<-----------------------------------------| 4
| | | | | |
| | | Direct Bubble to B | | |
5 |------------------------------------------------------------>|
| | | | | |
|Indirect Bubble to B via B's Teredo Server| | |
6 |----------------------------------------->|----------------->|
| | | | | |
| | | Direct Bubble to A | | |
|<------------------------------------------------------------| 7
| | | | | |
Port-Symmetric NAT to Address-Restricted NAT Packet
Exchange
Thaler Standards Track [Page 43]
RFC 6081 Teredo Extensions January 2011
1. A sends a direct bubble (Packet 1) destined to the mapped
address/port embedded in B's Teredo IPv6 address. The mapped
port in the source field of the packet assigned by Client A's
NAT is different from the mapped port embedded in A's Teredo
IPv6 address. This is characteristic of the port-symmetric NAT
positioned in front of A. The mapped address in the source
field of the packet is the same as the mapped address embedded
in the Teredo IPv6 address of A.
2. The aforementioned direct bubble is dropped by B's NAT because
it has not seen an outgoing packet destined to A's mapped IPv4
address.
3. A sends an indirect bubble (Packet 2) destined to B via Client
B's Teredo server.
4. The above-mentioned indirect bubble is received by B. B then
responds with the following packets. The first packet sent by B
is a direct bubble (Packet 3) destined to the mapped address/
port embedded in A's Teredo IPv6 address.
5. The above-mentioned direct bubble is dropped by A's NAT because
the NAT has not seen any outgoing packet sourced from the mapped
address/port embedded in A's Teredo IPv6 address and destined to
the mapped address/port embedded in B's Teredo IPv6 address.
6. B also sends an indirect bubble (Packet 4) destined to A via A's
Teredo Server.
7. The aforementioned indirect bubble is successfully received by
A. A responds to the indirect bubble with its own direct bubble
(Packet 5). This direct bubble is exactly the same as the first
direct bubble (Packet 1) sent by A.
8. This time around the aforementioned direct bubble is accepted by
B's NAT because the NAT has seen an outgoing packet (Packet 3)
sourced from the mapped address/port embedded in B's Teredo IPv6
address and destined to the mapped address/port embedded in A's
Teredo IPv6 address. It is important to remember that A's NAT
is port-symmetric and therefore varies only the mapped port
while the mapped address remains the same. B's NAT is address-
restricted and cares only about prior communication with the
IPv4 address, not the specific port. At this point,
communication in one direction is now possible (B to A, but not
vice versa).
Thaler Standards Track [Page 44]
RFC 6081 Teredo Extensions January 2011
9. After receiving the direct bubble, B remembers the new mapped
address/port that was in the source fields of the direct bubble
and uses those for future communication with A instead of the
mapped address/port embedded in A's Teredo IPv6 address.
10. A then times out and resends an indirect bubble (Packet 6) and
in response, B sends a direct bubble (Packet 7). This direct
bubble is destined to the new learned mapped address/port and
hence A's NAT permits the direct bubble through. Communication
is now possible in the other direction (client A to B).
6.2. UPnP-Enabled Symmetric NAT Extension
The following protocol example illustrates the use of the UPnP-
Enabled Symmetric NAT Extension in addition to the Symmetric NAT
Support Extension.
Assume that Teredo Client A, which is positioned behind a UPnP-
enabled port-symmetric NAT, wants to communicate with Teredo Client
B, which is also positioned behind a UPnP-Enabled port-symmetric NAT.
Before both clients start their qualification procedure, they use
UPnP to reserve port mappings on their respective NATs. The UPnP
operations succeed for both the clients and the clients hence know
that they are positioned behind UPnP-enabled NATs. After the
qualification procedure, both clients have valid Teredo IPv6
addresses because they both support the Symmetric NAT Support
Extension. Also, after the qualification procedure both clients will
compare their mapped address/port determined through UPnP with the
mapped address/port determined through the qualification procedure.
Because both will be the same, the clients will zero out their UPnP
mapped address/port values and conclude that they are each located
behind a single UPnP-enabled NAT.
The following packet exchange shows Teredo client A (A) establishing
communication with Teredo client B (B).
Thaler Standards Track [Page 45]
RFC 6081 Teredo Extensions January 2011
Teredo Client A's Client B's Teredo
Client Teredo Teredo Client
A NAT Server Server NAT B
| | | | | |
| | | Direct Bubble to B | | |
1 |------------------------------------------------------------>|
| | | | | |
|Indirect Bubble to B via B's Teredo Server| | |
2 |----------------------------------------->|----------------->|
| | | | | |
| | | Direct Bubble to A | | |
|<------------------------------------------------------------| 3
| | | | | |
UPnP-enabled Symmetric NAT Packet Exchange
1. A sends a direct bubble (Packet 1) to the mapped address/port
embedded in B's Teredo IPv6 address. Because A's NAT is a
symmetric NAT, the UDP source port field in the packet assigned
by A's NAT is different from the mapped port embedded in A's
Teredo IPv6 address, but the IPv4 source address of the packet is
the same as the mapped address embedded in A's Teredo IPv6
address.
2. The above-mentioned direct bubble is received by B because it is
destined for the UPnP mapped address/port of B and hence is let
through by the NAT. At this point, B deduces that A is
positioned behind a symmetric NAT because the mapped address/port
from which the direct bubble is received is different from the
mapped address/port that is embedded in A's Teredo IPv6 address.
Hence, it remembers that the peer is positioned behind a
symmetric NAT so that data packets will be sent to the mapped
address/port embedded in A's Teredo IPv6 address, rather than the
mapped address/port from which the direct bubble was received.
At this point, communication in one direction is now possible (B
to A, but not vice versa).
3. A also sends an indirect bubble (Packet 2) destined to B via B's
Teredo Server.
4. The above indirect bubble is received by B. B then responds with
a direct bubble (Packet 3) destined to the mapped address/port
embedded in A's Teredo IPv6 address, as in step 2.
5. Because A's NAT is also UPnP enabled, the above-mentioned direct
bubble is received by A. A also notices that B is positioned
behind a Symmetric NAT because the mapped address/port from which
the packet is received is different from the mapped address/port
Thaler Standards Track [Page 46]
RFC 6081 Teredo Extensions January 2011
embedded in B's Teredo IPv6 address. Hence, it remembers that
the peer is positioned behind a symmetric NAT so that data
packets will be sent to the mapped address/port embedded in B's
Teredo IPv6 address, rather than the mapped address/port from
which the direct bubble was received. At this point,
communication is now possible in the other direction (A to B).
6.3. Port-Preserving Symmetric NAT Extension
The following protocol example illustrates the use of the Port-
Preserving Symmetric NAT Extension.
Assume that Teredo Client A (A), which is positioned behind a port-
preserving symmetric NAT, wants to communicate with Teredo Client B
(B), which is also positioned behind a port-preserving symmetric NAT.
The following packet exchange explains the configuration setup and
communication setup between the two clients.
Thaler Standards Track [Page 47]
RFC 6081 Teredo Extensions January 2011
Teredo Client A's Client B's Teredo
Client Teredo Teredo Client
A NAT Server Server NAT B
| | | | | |
| | | Direct Bubble to B | | |
1 |--------------------------------------------------->| |
| | | | | |
|Indirect Bubble to B via B's Teredo Server| | |
2 |----------------------------------------->|----------------->|
| | | | | |
| | | Direct Bubble to A | | |
| |<--------------------------------------------------| 3
| | | | | |
| | | Direct Bubble to A | | |
| |<--------------------------------------------------| 4
| | | | | |
| | |Indirect Bubble to A via A's Teredo Server|
|<-----------------|<-----------------------------------------| 5
| | | | | |
| | | Direct Bubble to B | | |
6 |--------------------------------------------------->| |
| | | | | |
| | | Direct Bubble to B | | |
7 |------------------------------------------------------------>|
| | | | | |
|Indirect Bubble to B via B's Teredo Server| | |
8 |----------------------------------------->|----------------->|
| | | | | |
| | | Direct Bubble to A | | |
|<------------------------------------------------------------| 9
| | | | | |
Port-Preserving Symmetric NAT Packet Exchange
1. During the qualification procedure, when the clients receive a
response from the Teredo server, they compare the Port value in
the Origin indication with the Local Port value. If both values
match, the clients set the Port-Preserving NAT flag to TRUE.
2. When the response is received from the secondary Teredo server,
the mapped address/port value in the Origin indication is
compared with the mapped address/port value learned from the
response received from the primary server. If the mappings are
different, the Symmetric NAT flag is set to TRUE.
3. It is assumed that for both Clients A and B, the Port-Preserving
NAT flag and the Symmetric NAT flag are set to TRUE at the end
of the qualification procedure.
Thaler Standards Track [Page 48]
RFC 6081 Teredo Extensions January 2011
4. Before A sends packets to B, A checks to see if it is positioned
behind a port-preserving NAT and a symmetric NAT, which in the
example, it is. A also checks to see if the peer is "trusted",
but it currently is not. Next, A checks if the Random Port is
set to non-zero. Since it is still zero, A allocates a new
random port, begins listening on it, and stores the value in the
Random Port field.
5. A sends a direct bubble (Packet 1) from the primary port to the
mapped address/port embedded in B's Teredo IPv6 address. This
direct bubble does not have a Nonce Trailer or a Random Port
Trailer attached to the end.
6. The aforementioned direct bubble is dropped by B's NAT because
the NAT has not seen an outgoing packet destined to A's mapped
address.
7. A sends an indirect bubble (Packet 2) destined to B via client
B's Teredo server. This indirect bubble contains two trailers:
the Nonce Trailer containing a random nonce, and the Random Port
Trailer containing the random port value from the Peer Entry.
The nonce used in the Nonce Trailer is also stored in the Nonce
Sent field of the Peer Entry.
8. The aforementioned indirect bubble is received by B. B adds the
Teredo peer to its peer list. B saves the nonce value from the
Nonce Trailer in the Nonce Advertised field of the Peer Entry.
B stores the port value from the Random Port Trailer in the Peer
Random Port field in the Peer Entry.
9. B responds by sending the following packets. The first packet
sent by B is a direct bubble (Packet 3) destined to the mapped
address/port embedded in A's Teredo IPv6 address. This packet
is sent from the primary port. It includes the Nonce Trailer
with the nonce from the Nonce Advertised field of the Peer
Entry.
10. The aforementioned direct bubble is dropped by A's NAT because
the NAT has not seen any outgoing packet sourced from the mapped
address/port embedded in A's Teredo IPv6 address and destined to
the mapped address/port embedded in B's Teredo IPv6 address.
11. B then checks if it is positioned behind a port-restricted NAT
or a symmetric NAT. It also checks if the peer has already
advertised a random port. In this case, B is positioned behind
a port-preserving symmetric NAT and the peer has advertised a
random port; hence, it needs to use a random port. It checks if
its Random Port field is set to non-zero. Since it is still
Thaler Standards Track [Page 49]
RFC 6081 Teredo Extensions January 2011
zero, B allocates a new random port, begins listening on it, and
stores it in the Random Port entry of the Peer Entry. B then
sends a direct bubble (Packet 4) destined to the mapped address
embedded in A's Teredo IPv6 address and the port stored in the
Peer Random Port field of the Peer Entry. The direct bubble is
sent from its own random port.
12. The above direct bubble is dropped by A's NAT because the NAT
has not seen any outgoing packet sourced from the mapped address
embedded in A's Teredo IPv6 address and random port advertised
by A.
13. B also sends an indirect bubble (Packet 5) destined to A via A's
Teredo Server. This indirect bubble includes a Nonce Trailer
and a Random Port Trailer. The Nonce Trailer includes a new
randomly generated nonce that is also stored in the Nonce Sent
field of the Peer Entry. The Random Port Trailer includes the
value in the Random Port field of the Peer Entry.
14. The aforementioned indirect bubble is successfully received by
A. A parses the trailers and stores the nonce contained in the
Nonce Trailer in the Nonce Received field of the Peer Entry. A
stores the port advertised in the Random Port Trailer in the
Random Port field of the Peer Entry.
15. A responds with the following packets in response to the
indirect bubble received. The first packet is a direct bubble
(Packet 6) sent from the primary port and is destined to the
mapped address/port embedded in B's Teredo IPv6 address.
16. The aforementioned direct bubble again is dropped by B's NAT
because the NAT has not seen an outgoing packet with the same
4-tuple as the incoming packet.
17. The next packet is also a direct bubble (Packet 7) and this one
is sent from A's random port. The packet is destined to the
mapped address embedded in B's Teredo IPv6 address and the Peer
Random Port stored in the Peer Entry.
18. Because both NATs are port-preserving NATs and the random ports
have not been used for any other mapping, the aforementioned
direct bubble is received by B because B's NAT has seen an
outgoing packet (Packet 4) with the same address/port pairs. B
stores the address/port from which the direct bubble was
received in the mapped address/port fields of the Peer Entry.
It changes the status of the peer to "trusted" and sets the
Thaler Standards Track [Page 50]
RFC 6081 Teredo Extensions January 2011
Direct Receive on Random Port field to TRUE. At this point,
communication in one direction is now possible (B to A, but not
vice versa).
19. Because A still considers B to be "not-trusted", it times out
and retransmits an indirect bubble (Packet 8). This packet
contains a new nonce as part of the Nonce Trailer and also
contains the value of the random port as part of the Random Port
Trailer.
20. B receives the aforementioned indirect bubble. The processing
of this indirect bubble is similar to the processing of Packet
2. Since B received a direct bubble on its random port, it does
not respond with a direct bubble from its primary port.
Instead, it responds with a direct bubble (Packet 9) sent from
its random port, which is similar to Packet 4 mentioned above.
21. A receives the direct bubble sent by B. A stores the mapped
address/port from which the direct bubble was received in mapped
address/port fields in the Peer Entry. A changes the status of
B to "trusted" and sets the Direct Receive on Random Port field
to TRUE. At this point, the communication is now possible in
the other direction (A to B).
6.4. Sequential Port-Symmetric NAT Extension
The following protocol example illustrates the use of the Sequential
Port-Symmetric NAT Extension.
Assume that Teredo Client A (A), which is positioned behind a
sequential port-symmetric NAT and implements the Sequential Port-
Symmetric NAT Extension, wants to communicate with Teredo Client B
(B), which is positioned behind a port-restricted NAT that supports
the Port-Preserving Port-Symmetric NAT Extension. The following
packet exchange explains the configuration setup and communication
setup between the two clients.
Thaler Standards Track [Page 51]
RFC 6081 Teredo Extensions January 2011
Teredo A's A's B's
Client Primary Secondary Teredo Client
A NAT Server Server Server NAT B
| | | | | | |
| Direct Bubble to B | | | | |
1 |-------------------------------------------------->| |
| | | | | | |
|Router Solicitation | | | | |
2 |------------------->| | | | |
| | | | | | |
|Router Advertisement| | | | |
|<-------------------| 3 | | | |
| | | | | | |
4 | Direct Bubble to B | | | | |
|-------------------------------------------------->| |
| | | | | | |
| Router Solicitation | | | |
5 |---------------------------->| | | |
| | | | | | |
| Router Advertisement | | | |
|<----------------------------| 6 | | |
| | | | | | |
| Indirect Bubble to B via B's Teredo Server | | |
7 |------------------------------------------->|-------------->|
| | | | | | |
| | | | Direct Bubble to A |
| |<-------------------------------------------------| 8
| | | | | | |
| | | | Indirect Bubble to A |
|<-------------------|<--------------------------------------| 9
| | | | | | |
| | | | Direct Bubble to A |
|<-----------------------------------------------------------| 10
| | | | | | |
| Direct Bubble to B | | | |
11 |----------------------------------------------------------->|
Sequential Port-Symmetric NAT Packet Exchange
1. During the qualification procedure, when Client A receives a
response from the Teredo Server, it compares the Port value in
the Origin indication with the Local Port value. Since they are
different, it concludes that it is not behind a port-preserving
NAT, and so assumes it is behind a sequential port-symmetric NAT.
2. When A wants to communicate with B, A starts by sending a direct
bubble (Packet 1) from its primary port. This occurs because
Client A does not know Client B's NAT type, which could be a cone
Thaler Standards Track [Page 52]
RFC 6081 Teredo Extensions January 2011
or address restricted NAT or UPnP-enabled NAT. Because Client A
is behind a symmetric NAT, the external port used by A's NAT is a
new port. This direct bubble will be dropped by B's NAT since
Client B is behind a port-restricted NAT.
3. Because Client A does not know if B is behind a port restricted
NAT or some other kind of NAT, Client A proactively opens a new
random internal port, say, port 1100.
4. Client A then performs its Echo Test as follows:
A. Client A sends a router solicitation (Packet 2) to its Teredo
Server address from port 1100. The server responds with a
router advertisement (Packet 3).
B. Client A sends a direct bubble (Packet 4) to the peer from
port 1100 destined to the port advertised in Client B's
Teredo address, say, port 2100. This direct bubble is
dropped by Client B's port-restricted NAT.
C. Client A sends a router solicitation (Packet 5) to its
secondary Teredo server address from port 1100. The server
responds with a router advertisement (Packet 6).
D. On receiving the corresponding router advertisements for
Packet 2 and Packet 4, Client A knows that port 1100 maps to,
say, port 1200 for Packet 2 and port 1202 for Packet 4.
E. Client A then calculates its predicted port used for Packet 2
as the average (rounded down) of 1200 and 1202, i.e., 1201.
5. Client A then sends out an indirect bubble (Packet 7). This
indirect bubble contains a random port trailer that contains the
predicted port, port 1201. This indirect bubble makes it to
Client B.
6. Client B sends out the following bubbles in response to the
indirect bubble:
A. The first direct bubble (Packet 8) is destined for the port
mapping embedded in Client A's Teredo Address. (It has been
observed that some NATs display symmetric NAT behavior for
outgoing packets but cone NAT behavior for incoming packets.
The direct bubble described is likely to succeed if Client
A's NAT displays such a behavior.) Since in this example,
A's NAT is a normal sequential port-symmetric NAT, this
packet is dropped.
Thaler Standards Track [Page 53]
RFC 6081 Teredo Extensions January 2011
B. The second packet is an indirect bubble (Packet 9) sent to
Client A without any trailers since Client B is behind a
port-restricted NAT.
C. The next packet will be a direct bubble (Packet 10) sent to
port 1201. This packet will make it in to Client A since
Client A previously sent an outgoing packet (Packet 4) with
the same four tuple. At this point, communication in one
direction is now possible (A to B, but not vice versa).
7. Client A then sends a direct bubble (Packet 11) to Client B when
it receives Packet 10. This time, the bubble makes it through to
B because it previously sent an outgoing packet (Packet 10) with
the same four tuple. At this point, communication is now
possible in the other direction (B to A).
6.5. Hairpinning Extension
The following protocol example illustrates the use of the Hairpinning
Extension.
In Figure 3 (Section 3.5), Teredo Client A (A) and Teredo Client B
(B) are positioned behind different immediate NATs in a two-layer NAT
topology; that is, the outermost NAT (NAT E) is common to both A and
B but the immediate NATs that they are connected to are different (A
is connected to NAT F while B is connected to NAT G). Further assume
that the immediate NATs that A and B are connected to are UPnP-
enabled (NAT F and NAT G are UPnP-enabled). We assume that NAT E
does not support hairpinning; that is, the NAT does not relay packets
originating from the private address space and destined for the
public address of the NAT, back to the private address of the NAT.
Before starting the qualification procedure, both A and B use UPnP to
reserve port mappings on their respective NATs. They observe that
the UPnP operation succeeds and both clients obtain valid UPnP Mapped
Address/Port values.
Next, both client A and client B implement the qualification
procedure where they determine their mapped address/port values, as
specified in Section 5.2.1 of [RFC4380].
A and B both compare their UPnP Mapped Address/Port values with the
mapped address/port values obtained through the qualification
procedure. Because both A and B are part of a two-layer NAT
topology, these values will be different. Hence, both A and B
continue to hold on to their UPnP Mapped Address/Port.
Thaler Standards Track [Page 54]
RFC 6081 Teredo Extensions January 2011
The following packet exchange shows client A establishing
communication with client B.
Teredo Teredo Client A's Client B's
Client NAT Client NAT NAT Teredo Teredo
A F B G E Server Server
| | | | | | |
| | Direct Bubble to B | | | |
1 |-------------------------------------->| | |
| | | | | | |
| Indirect Bubble to B via B's Teredo Server |
2 |----------------------------------------------------------->|
| | |<----------------------------------------|
| | | | | | |
| | | Direct Bubble to A | | |
3 | | |------------------->| | |
| | | | | | |
| | | Direct | | | |
| | |Bubble to A| | | |
4 | | |---------->| | | |
| | | | | | |
| | | Direct | | | |
| | |Bubble to A| | | |
5 | | |---------->| | | |
|<-----------------------------| | | |
| | | | | | |
| | | Indirect Bubble to A | |
6 | | |---------------------------->| |
|<-----------------------------------------------| |
| | | | | | |
|Direct Bubble to B| | | | |
7 |----------------->| | | | |
| | | | | | |
Hairpinning-Based Packet Exchange
1. A sends a direct bubble (Packet 1) to the mapped address/port
embedded in B's Teredo IPv6 address.
2. The aforementioned direct bubble is dropped by NAT E, because it
does not support Hairpinning.
3. A sends out an indirect bubble (Packet 2) destined to B via B's
Teredo Server. In this indirect bubble, A includes an Alternate
Address Trailer that includes both the local address/port and
the UPnP mapped address/port.
Thaler Standards Track [Page 55]
RFC 6081 Teredo Extensions January 2011
4. The aforementioned indirect bubble is received by B. After
parsing the Alternate Address Trailer, B has a total of three
addresses to communicate with: two from the Alternate Address
Trailer and one from the mapped address/port embedded in A's
Teredo IPv6 address. B then responds with the following
packets. The first packet sent by B is a direct bubble (Packet
3) destined to the mapped address/port embedded in A's Teredo
IPv6 address.
5. The aforementioned direct bubble will be dropped by the NAT E
because it does not support Hairpinning.
6. Because the local address/port was the first mapping in the
Alternate Address Trailer, the second direct bubble (Packet 4)
sent by B is destined to the local address/port.
7. The aforementioned direct bubble is dropped because A and B are
positioned behind different NATs and hence have their own
private address space. A's local address is not reachable from
B.
8. The next direct bubble (Packet 5) is sent by B destined to A's
UPnP mapped address/port, which is the second mapping in the
Alternate Address Trailer sent by A.
9. The aforementioned direct bubble is received by A because A's
UPnP-mapped address is reachable from B. A stores the source
address from which the direct bubble was received in the mapped
address/port fields of the Peer Entry, as defined in Section 5.2
of [RFC4380]. Also, the mapped address status field (as
specified in Section 5.2.3 of [RFC4380]) is changed to
"trusted". At this point, communication in one direction (A to
B) is now possible, but not vice versa because B has not yet
marked A as trusted.
10. B also sends an indirect bubble (Packet 6) to A via A's Teredo
server. As part of the indirect bubble, B also includes an
Alternate Address Trailer, which contains the local address/port
and the UPnP mapped address/port of B.
11. The aforementioned indirect bubble is received by A. After
parsing the Alternate Address Trailer, A adds the two addresses
in the Alternate Address Trailer to the Alternate Address List
in the Peer Entry. Because the peer's mapping is "trusted"
(point 9), A responds with only one direct bubble (Packet 7)
that is sent to the mapped address/port stored in the Peer
Entry.
Thaler Standards Track [Page 56]
RFC 6081 Teredo Extensions January 2011
12. The aforementioned direct bubble is received by B. B records
the mapped address/port from which the direct bubble was
received in the mapped address/port field in its Peer Entry, and
changes the status of the mapped address to "trusted". At this
point, communication is now possible in the other direction (B
to A).
6.6. Server Load Reduction Extension
The following protocol example illustrates the use of the Server Load
Reduction Extension.
Assume that Teredo Client A (A) has established communication with
Teredo Client B (B). Also, assume that at some later point when no
data packets have been exchanged between both clients for more than
30 seconds, the communication needs to be re-established because A
wants to send a data packet to B.
The following packet exchange helps A re-establish communication with
B.
Teredo Client A's Client B's Teredo
Client Teredo Teredo Client
A NAT Server Server NAT B
| | | | | |
| | | Direct Bubble to B | | |
1 |------------------------------------------------------------>|
| | | | | |
| | | Direct Bubble to A | | |
|<------------------------------------------------------------| 2
| | | | | |
Server Load Reduction Packet Exchange
1. A sends a direct bubble (Packet 1) with the Neighbor Discovery
Option Trailer, with the DiscoveryType field set to
TeredoDiscoverySolicitation.
2. If the mapping on either of the NATs has not expired, the direct
bubble is received by B. B parses the Neighbor Discovery Option
and because the DiscoveryType was set to
TeredoDiscoverySolicitation, B responds with a direct bubble
(Packet 2). B's direct bubble also contains the Neighbor
Discovery Option and the DiscoveryType is set to
TeredoDiscoveryAdvertisement.
Thaler Standards Track [Page 57]
RFC 6081 Teredo Extensions January 2011
3. The aforementioned direct bubble is received by A and at this
point, communication between the Teredo clients is re-
established.
7. Security Considerations
Security considerations are the same as those specified in Section 7
of [RFC4380].
In addition, the Hairpinning Extension introduces the possibility of
an amplification attack if a malicious user could advertise a large
number of port mappings in the Alternate Address Trailer, resulting
in a large number of direct bubbles sent in response. Because of
this, Section 4.3 explicitly limits the number of addresses that a
Teredo client will accept.
Because the nonce in the Nonce Trailer is used (as specified in
Section 5.2.4.4) to prevent spoofing of bubbles that would result in
directing traffic to the wrong place, it is important that the nonce
be random so that attackers cannot predict its value. See [RFC4086]
for further discussion of randomness requirements.
8. Acknowledgements
Thanks to Gurpreet Virdi and Poorna Gaddehosur for technical
contributions to this document, and to the V6OPS WG and Jari Arkko
for their helpful reviews.
9. IANA Considerations
IANA has created a new trailer Type registry. Requests for new
trailer Type values are made through Specification Required
[RFC5226]. Initial values are listed below.
Trailer Type Usage Reference
------------ --------------------------------- ---------
0x01 Nonce Trailer RFC 6081
0x02 Random Port Trailer RFC 6081
0x03 Alternate Address Trailer RFC 6081
0x04 Neighbor Discovery Option Trailer RFC 6081
10. References
10.1. Normative References
[RFC1918] Rekhter, Y., Moskowitz, R., Karrenberg, D., Groot, G.,
and E. Lear, "Address Allocation for Private Internets",
BCP 5, RFC 1918, February 1996.
Thaler Standards Track [Page 58]
RFC 6081 Teredo Extensions January 2011
[RFC2119] Bradner, S., "Key words for use in RFCs to Indicate
Requirement Levels", BCP 14, RFC 2119, March 1997.
[RFC2460] Deering, S. and R. Hinden, "Internet Protocol, Version 6
(IPv6) Specification", RFC 2460, December 1998.
[RFC4380] Huitema, C., "Teredo: Tunneling IPv6 over UDP through
Network Address Translations (NATs)", RFC 4380,
February 2006.
[RFC4861] Narten, T., Nordmark, E., Simpson, W., and H. Soliman,
"Neighbor Discovery for IP version 6 (IPv6)", RFC 4861,
September 2007.
[RFC5226] Narten, T. and H. Alvestrand, "Guidelines for Writing an
IANA Considerations Section in RFCs", BCP 26, RFC 5226,
May 2008.
[UPNPWANIP] UPnP Forum, "WANIPConnection:1", November 2001,
.
10.2. Informative References
[RFC4086] Eastlake, D., Schiller, J., and S. Crocker, "Randomness
Requirements for Security", BCP 106, RFC 4086,
June 2005.
[RFC4443] Conta, A., Deering, S., and M. Gupta, "Internet Control
Message Protocol (ICMPv6) for the Internet Protocol
Version 6 (IPv6) Specification", RFC 4443, March 2006.
[RFC4787] Audet, F. and C. Jennings, "Network Address Translation
(NAT) Behavioral Requirements for Unicast UDP", BCP 127,
RFC 4787, January 2007.
Author's Address
Dave Thaler
Microsoft Corporation
One Microsoft Way
Redmond, WA 98052
USA
Phone: +1 425 703 8835
EMail: dthaler@microsoft.com
Thaler Standards Track [Page 59]
RFC, FYI, BCP